Ramkumar

MrPLC Member
 View profile  See their activity

  • Content count

    29

  • Joined

  • Last visited

Community Reputation

0 Neutral

About Ramkumar

  • Rank
    Sparky

Profile Information

  • Country India

  1. Automatic disconnection of VNC viewer from GOT2000 HMI

    Ramkumar replied to Ramkumar's topic in Mitsubishi

    Thanks a lot for the response sir !

  2. Automatic disconnection of VNC viewer from GOT2000 HMI

    Ramkumar replied to Ramkumar's topic in Mitsubishi

    Hi, please guide on this topic if someone has an idea...

  3. Automatic disconnection of VNC viewer from GOT2000 HMI

    Ramkumar replied to Ramkumar's topic in Mitsubishi

    Hi VeeB, I set the "Guaranteed Time" to 60 seconds and expected the VNC connection to close. Waited for more than that time and the connection didn`t closed. Kindly advise on this.

  4. Automatic disconnection of VNC viewer from GOT2000 HMI

    Ramkumar replied to Ramkumar's topic in Mitsubishi

    Hi VeeB, Thanks a lot for the response ! It was highly helpful. Please let me know of the disconnection shall be triggered from the HMI if we want to disconnect the VNC clients...?
  5. Ramkumar started following Automatic disconnection of VNC viewer from GOT2000 HMI
  6. Hi, I would like to automatically close the VNC viewer connection, which is used to view the GOT2000 HMI remotely. Very interested to know if any options are available. Thanks in advance !!!
  7. Ramkumar started following Tight VNC HMI connection getting automatically disconnected
  8. Hi, The Tight VNC is disconnecting us automatically after minutes of operation. Could you advise us if there is any particular setting in the GT Works, which is controlling this... Thanks in advance.. Ramkumar  

  9. Multiple TCP slave connections at RJ71EN71

    Ramkumar replied to Ramkumar's topic in Mitsubishi

    Please find the attachd image of error
  10. Hi, We are receiving an error "*Error** PLC of all MODBUS/TCP connection modules Port No. is mismatched. When using multiple MODBUS/TCP connection modules, PLC of all MODBUS/TCP connection modules Port No. must be matched.   MODBUS/TCP Connection Module  NV_E02435" while trying to add two slave connections with different port numbers.....Please clarify on this error...
  11. Ramkumar started following Multiple TCP slave connections at RJ71EN71
  12. Yes Gambit, it is connected to the battery. Only part of the retentive area is getting wiped off..
  13. Ramkumar started following mitsubishi R08 plc retentive area cleared after power cycling
  14. Mitsubishi R08 plc retentive area cleared after power cycling or remote reset. Please clarify on this issue.

  15. Remote reset R08 PLC from HMI

    Ramkumar replied to Ramkumar's topic in Mitsubishi

    Hi Gambit, what do you think about the reset communication option, If yes, could you give an implementation snapshot please... Restart communications.pdf

  16. Remote reset R08 PLC from HMI

    Ramkumar replied to Ramkumar's topic in Mitsubishi

    Yes, that is mentioned in the manual, but not known to me...

  17. Remote reset R08 PLC from HMI

    Ramkumar replied to Ramkumar's topic in Mitsubishi

    Hi Gambit, We are using both R16 and R08 CPU`s. In the screenshot, the module number is 0060 and slot is 4. Please advise on this.
  18. Ramkumar started following Remote reset R08 PLC from HMI

  19. Remote reset R08 PLC from HMI

    Ramkumar replied to Ramkumar's topic in Mitsubishi

    Hi Gambit, I tried to do the same code to reset the module RJ71EN71. But received the attached error. The module number indicated in the PLC is 0060. So I used 006, which is indicated as 6. Please help me on this error.

  20. Remote reset R08 PLC from HMI

    Ramkumar replied to Ramkumar's topic in Mitsubishi

    Hi Gambit, I tried to use the GP_ERRCLEAR just now... Is it possible for you to help me by providing an implementation screenshot ? I`m confused with the parameters Un, S and d