Forums.MrPLC.com: Free Software B&R - Forums.MrPLC.com

Jump to content

Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

Free Software B&R Rate Topic: -----

#1
User is offline   Husanto 

  • Sparky
  • PipPipPip
  • Group: MrPLC Member
  • Posts: 40
  • Joined: 21-June 07
  • Location:Jakarta - Indonesia
  • Interests:Reading Books, write a books, and etc.
  • Country:Indonesia
    Indonesia
Hi all,

I have problem about PLC B&R with Type EX290, i want to check the problem but i don't a software and the cable, can any body tell me what software i must to use and where i can find the software for free??

Thanks
0

#2
User is offline   Crossbow 

  • Automation Engineer
  • Group: MrPLC Admin
  • Posts: 3,601
  • Joined: 30-January 03
  • Gender:Male
  • Location:Edge of Insanity
  • Country:United States
    United States
Contact B&R directly and ask them. I do not think the software is free.
0

#3
User is offline   ric_s 

  • Hi, I am New!
  • Pip
  • Group: MrPLC Member
  • Posts: 1
  • Joined: 15-March 09
  • Country:Australia
    Australia

View PostHusanto, on Mar 28 2009, 05:50 PM, said:

Hi all,

I have problem about PLC B&R with Type EX290, i want to check the problem but i don't a software and the cable, can any body tell me what software i must to use and where i can find the software for free??

Thanks


You need to use Automation Studio. There is an evaluation version available here:

http://www.br-automation.com/cps/rde/xchg/...evel_1=Software

You will need a copy of the project as well as B&R PLC's don't allow for uploading...
0

#4
User is offline   B&RSupport 

  • Hi, I am New!
  • Pip
  • Group: MrPLC Member
  • Posts: 4
  • Joined: 13-February 10
  • Country:United States
    United States
Hello,

EX290 is not a PLC but an X2X bus controller for System 2003 product line. The PLC would be something like CP474 or CP476.

To connect to the PLC, you need a straight RS232 cable and a program called PVI Transfer.
You can download it for free here: http://www.br-automation.com/cps/rde/xchg/...10_ENG_HTML.htm

You can use this program to download the logbook (error log) from the PLC.

Automation Studio is used for development or maintenance. You only need if you are going to program the PLC.

If you are sure the problem is with EX290, you need to look at the LEDs. They are described in the datasheet.
http://www.br-automation.com/cps/rde/xchg/...29_ENG_HTML.htm

EX290 has no programming of its own.

If all else fails, please contact B&R technical support at the link below.
http://www.br-automation.com/cps/rde/xchg/...40_ENG_HTML.htm
0

#5
User is offline   Alvi 

  • Hi, I am New!
  • Pip
  • Group: MrPLC Member
  • Posts: 3
  • Joined: 05-August 09
  • Country:Pakistan
    Pakistan
HI
its amazing i have same problem and i also want free software plz tell me any solution for this
thanks
0

#6
User is offline   Crossbow 

  • Automation Engineer
  • Group: MrPLC Admin
  • Posts: 3,601
  • Joined: 30-January 03
  • Gender:Male
  • Location:Edge of Insanity
  • Country:United States
    United States
Alvi,

As was clearly stated in this thread, the software is not free, and there was a link for a demo version.

Nobody on these forums will make illegal copies of software for you, it is against the terms of service to even talk about it in the forums.

Please read the whole thread before replying.
0

#7
User is offline   atmoha 

  • Sparky
  • PipPipPip
  • Group: MrPLC Member
  • Posts: 14
  • Joined: 16-August 13
  • Country:Poland
    Poland
But how to register in that web site ?
there is no option for registration.
by this way could you please give me another web site for downloading automation studio? i need it for my studies
best regards

This post has been edited by atmoha: 18 August 2013 - 09:33 AM

0

#8
User is offline   Crossbow 

  • Automation Engineer
  • Group: MrPLC Admin
  • Posts: 3,601
  • Joined: 30-January 03
  • Gender:Male
  • Location:Edge of Insanity
  • Country:United States
    United States
This topic is 3 1/2 years old. I highly doubt the original poster is reading it.

Did you try to contact B&R to ask about it? Call them and ask, or email through that website.
0

Share this topic:


Page 1 of 1
  • You cannot start a new topic
  • You cannot reply to this topic

1 User(s) are reading this topic
0 members, 1 guests, 0 anonymous users