warkan

MrPLC Member
  • Content count

    19
  • Joined

  • Last visited

Community Reputation

0 Neutral

About warkan

  • Rank
    Sparky

Profile Information

  • Country Malaysia
  1. Cx-programmer

    Hey ! The program i have uploaded has a error : [Ladder Section Name : Section1] ERROR: Rung 36 - Redundant circuit. ERROR: Rung 37 - Redundant circuit. ERROR: Rung 38 - Redundant circuit. ERROR: Rung 39 - Redundant circuit. [Ladder Section Name : END] Not sure what this means !!! COMPARISON INSTRUCTION EQUAL TO AND THIS INSTRUCTION IS ASSIGNED WITH A NUMBER 300 BUT I DONT KNOW WHY 300 DOES NOT APPEAR IN THIS PLACE Please help.. Untitled.cxp
  2. Automatic parking system

    Ah! so if you look in to that program file which I uploaded, on page 8 the first input Car_In_Pos_A1 is the only ACTUAL input from the I/O list. The OR gate along with it is within the program. So in this case I use W for this and latch it with the output ?
  3. Rslogix500 to CX-programmer

    Yeah I understand thatt... was just looking for tutorials that could help me do the job..
  4. Automatic parking system

    I have attached the program that I want to reproduce on CX Programmer V 9.3. So going to page 8, how would my addressing change ? Some people suggested me to use W in front of the Inputs/outputs rather than just entering the address number directly.. How do I decide this is the address for this this contact and this bit number is what it is ? These are my inputs and outputs : 1. CI0 0.00 In Gate Car Waiting 2. CIO 0.01 In Gate Car Entered 3. CIO 0.02 In Gate Motor Running 4. CIO 0.03 Out Gate Car Waiting 5. CIO 0.04 Out Gate Car Out 6. CIO 0.05 Out Gate Motor Running 7. CIO 0.06 Car in Position A1 8. CIO 0.07 Car in Position A2 9. CIO 0.08 Car in Position A3 10. CIO 0.09 Car in Position B1 11. CIO 0.10 Car in Position B2 12. CIO 0.11 Car in Position B3 13. CIO 1.00 Lift 1 Pushbutton 14. CIO 1.01 Lift 1 Motor Running 15. CIO 1.02 Car Waiting for Lift 1 on Floor G 16. CIO 1.03 Car Waiting for Lift 1 on Floor A 17. CIO 1.04 Lift 1 at Floor G 18. CIO 1.05 Lift 1 at Floor A 19. CIO 1.06 Lift 2 Pushbutton 20. CIO 1.07 Lift 2 Motor Running 21. CIO 1.08 Car Waiting for Lift 2 on Floor G 22. CIO 1.09 Car Waiting for Lift 2 on Floor A 23. CIO 1.10 Lift 2 at Floor G 24. CIO 1.11 Lift 2 at Floor A 1. CIO 100 .04 In Gate Up Direction 2. CIO 100 .05 In Gate Down Direction 3. CIO 100 .06 Out Gate Up Direction 4. CIO 100 .07 Out Gate Down Direction 5. CIO 101.04 Lift 1 Up Direction 6. CIO 101.05 Lift 1 Down Direction 7. CIO 101.06 Lift 2 Up Direction 8. CIO 101.07 Lift 2 Down Direction PROGRAM (1).pdf
  5. Rslogix500 to CX-programmer

    Hand converting is where I am having trouble with since I have not had much experience .. XD
  6. Np-Designer v 1.1 Error - URGENT!

    OMG ! Why did I not think of this earlier ? It worked like a charm. Thank you ! SO no tutorials ? :(
  7. Np-Designer v 1.1 Error - URGENT!

    To see the save as option I need to be able to open the file firstly yeah ? It gives an instant error saying that and goes blank after clicking close on the error dialogue box. Oh if you have some experience on Np Designer, Could you give me some tips/ tutorials that you may have used to learn it ? I am new to this field and finding it tricky to be able to communicate between HMI and the PLC itself.. For instance, How do I design a push button on the HMI that will be able to control the movement of a lift/gate manually ? The addressing of the PLC and HMI should match or something ?
  8. Rslogix500 to CX-programmer

    Thanks! But, I guess you will have to pay some amount to get it done yeah ? Mine is just a school project and I don't think I would be able spend so much for this :(
  9. Automatic parking system

    Does CX-programmer have a command called ONS- one shot ? Also, if you have any tips on how the addressing the works that would be very helpful ! I get confused with the 0.00 and stuff.
  10. Np-Designer v 1.1 Error - URGENT!

    And ohh do you have any videos tutorials for NP designer ? The ones I found online were all other models..
  11. Np-Designer v 1.1 Error - URGENT!

    yeah sorry I misunderstood it !! When the file name is short, it does not give this error. However, I can't rename the original file and will have to recreate the project.
  12. Hey guys! So I have a file which was created on RSlogix. But, I want to use the same file on CX-Programmer for OMRON. Is there any shortcut to do it ? Or will I have to recreate the program from scratch ? If that is the case, any tips on creating this file from scratch ? I am pretty new to ladder logic programming and my basics aren't too strong ! So even minute details would help... Thanks so much in advance!! PROGRAM (1).pdf
  13. Np-Designer v 1.1 Error - URGENT!

    No !! I just tried opening the same saved file and it gives me that error :( Not sure why :S Any other possibilities ?
  14. Np-Designer v 1.1 Error - URGENT!

    GUYS i fixed the error and now I am able to save a file.However after I save a file when I open it now I get the following error :( error.bmp
  15. Np-Designer v 1.1 Error - URGENT!

    hey guys ! When I try saving a file this is the error i get.. I tried reinstalling and it seemed to work fine for a few times and then i get this error again... PLEASEE HELP !!! very urgent :( here are the screen shots of the errors: the system cannot find the path specified.bmp environment parameter fail.bmp