-
Content count
453 -
Joined
-
Last visited
Community Reputation
13 GoodAbout ParaffinPower
-
Rank
Sparky
- Birthday 01/24/71
Contact Methods
- Website URL http://
Profile Information
- Location Manchester
- Country United Kingdom
Recent Profile Visitors
-
b.k.n. liked a post in a topic: Relative Move NX1P2 and 1SN drive
-
ParaffinPower started following Relative Move NX1P2 and 1SN drive
-
Relative Move NX1P2 and 1SN drive
ParaffinPower replied to taxidelt's topic in NJ Series / Sysmac Studio
This is true for everything :) -
willer liked a file: CP1H Operation Manual
-
Guest liked a post in a topic: Recipes using NB HMI + CP1
-
Am trying to use your HHMMSS FBs Paraffin Power. Do I have to use both timers and the one shot? Cant seem to get the timer started.
Regards
-
ParaffinPower liked a post in a topic: E-Designer
-
ParaffinPower started following E-Designer
-
Hi Clandy Give Beijer in the UK a bell. Excellent team.
-
AlexeyN78 liked a file: HHMMSS.cxf
-
Janaka Angampitiya liked a post in a topic: [PLC Sample Code] - CP1L and CP1H EasyModbus FB
-
ParaffinPower started following Good Quality Affordable HMI & SCADA
-
Beijer x2 family mate
-
Beijer make a great daylight readable Hmi which talks Ethernet/ip to NJ or NX controllers.
-
ParaffinPower started following daylight readable omron HMI solution?
-
How to set MX2 so it starts ("RUN") automatically after power on
ParaffinPower replied to Mantas Rukuiža's topic in CX-One
Wire the run signal through the 'ready ' output relay -
ParaffinPower liked a post in a topic: 2 HMI's 1 plc.
-
ParaffinPower started following GOT recipe record list.
-
Beijer's X2 and their old E1000 handle recipes infinitely better.
-
ParaffinPower started following E1012 to GOT2000 conversion
-
I've found the e1000 to Beijer iX conversion tool a better bet. And you end up with a better Hmi, too. Included in iXDeveloper
-
ParaffinPower liked a post in a topic: What is the benefit of using Structured programming?
-
ParaffinPower started following What is the benefit of using Structured programming?
-
What is the benefit of using Structured programming?
ParaffinPower replied to wlederer's topic in Mitsubishi
I think this is a problem specific to Mitsubishi, confirming my opinion that it should be thrown in the bin. -
ParaffinPower started following E-Designer Software
-
Still for sale, it's not expensive.
-
Thanks
-
ParaffinPower started following CP1L EM as Modbus tcp client.
-
Hello Not used Cp1L in a long time. Can the CP1L EM be a Modbus Client? Is there a FB? And if yes, can it talk to multiple servers? Thanks
-
Is it not just a slow Hmi?
-
phuc liked a post in a topic: [PLC Sample Code] - CP1L and CP1H EasyModbus FB
-
'Slave Application Error" with NX-ECC20x
ParaffinPower replied to vanquangtk's topic in NJ Series / Sysmac Studio
The 'backplane' connection with the Nx I/O is rubbish. I had endless problems with a system. This was one of the million errors that would randomly appear. Omron recommend cleaning the contacts and fitting clamps either end to hold it together. Of course, ether cat is not a silver bullet and all usual noise mitigation techniques are required. Pp -
ParaffinPower liked a post in a topic: Temperature control; motorised gas valve
-
Temperature control; motorised gas valve
ParaffinPower replied to ParaffinPower's topic in General Topics - The Lounge
Thanks for the replies. Your last guess is right. It stays where I leave it. I can move the actuator but then do I have to wait to monitor the temperature response?