naresh_pt

MrPLC Member
  • Content count

    14
  • Joined

  • Last visited

Community Reputation

0 Neutral

About naresh_pt

  • Rank
    Sparky

Contact Methods

  • ICQ 0

Profile Information

  • Gender Male
  • Country India
  1. FX-3U With MR-E100 Servo

    Great, Thanks for the info.
  2. FX-3U With MR-E100 Servo

    ok got it, fx3u can be programmed using gx-developer for this Servo application. I got the demo version from this site. Now my question is abt HMI, my HMI is GT 1055, which is the software for this HMI. Will GT designer 2 do.
  3. FX-3U With MR-E100 Servo

    Thanks for the information. Is the GX Works 2 demo version available, can you share the link please.
  4. FX-3U With MR-E100 Servo

    I am coming back to Servo systems after few years and need help on starting on Mitsubishi Servo system. My System is FX-3U-64MT With MR-E100 Servo. can you please provide help on below doubts. Which is the software to program FX-3U PLC to control Servo system. What is the latest version & where can I get a demo version Do I need to use 2 different software for PLC & Servo
  5. AJ71QE71N PORT No setting

    HI All, currently I am working with Q2A PLC of mitsubishi & AJ71QE71 Ethernet Module. I have managed to set the IP Address & can ping it. But for doing communication with IOServer I need to set the PORT No. & Protocol(TCP/UDP) setting of the the Ethernet Module(AJ71QE71) In the software there is no setting for this. If anybody knows abt this pls. tell me the setting procedures. Regards, Naresh P.
  6. WRITING REAL NUMBER

    Hi all, Can any body tell me that how to write Real_Flot) Number in adata registers in PLC program. to write integer 100 in data register D1 we write thr instruction [MOV K100 D1] For writing Real value what should be the statement. Regards Naresh P.
  7. QJ17C24N SERIAL Module

    Hi, I am working on Q Series of PLCS (Q2 & Q12PH). I am trying to communicate the PLCs with serial Server using serial communication modules QJ71C24N. I have managed to do communicattion between the Server(PC) & the individual PLCs using the RS232 Port on the Modules. Now I want to do use RS485/422 multidrop n/w i.e. PC(Server) communicates with Q2 PLC on RS232(which is working now) ,Q2 & Q12 PLCS are connected on RS 485/422 Ports. I want to do communication betwwen PC(Server) & Q12 PLC through Q2 PLC. can anybody tell me the software switch settings in GXDeveloper for this. Secondly How to configure the port as RS422 or RS485, as this will decide the terminating resistors value. current switch setting : for Q2 : SW1 7E7 SW2 5 SW3 737 SW4 5 SW5 0 for Q12: SW1 7E7 SW2 5 SW3 737 SW4 5 SW5 1 MRPLC_Q.bmp
  8. Melsecnet

    Hello Everybody, Currently I am working om MELSECNET of mitsubishi. I am using Q02 & Q12PH CPU for the MELSECNET n/w. n/w Setting is done in one PLC only i.e Q02 AS FOLLOWS MESECNET/10(Control station) STARTING IO NO. 0 N/W NO. 1 TOTAL STATIONS 2 GROUP NO 0 USING THIS IT IS WORKING FOR B & W, BUT it is not working for X & Y , I have done the setting in the LX/LY screen. Specified 1 PLC as I/O MASTER , M -> L Y0-Y1F X0-X1F BUT IT IS NOT WORKING FOR X/Y, If anybody knows abt. this pls. tell me the setting. Thanks Naresh
  9. Qj71c24 Serial

    Hi Panic mode, Yes I have seen that thread which u have mentioned thats for ethernet, now i am working on serial communication of QJ71C24N & PC.The CPU I am using is Q02HCPU of Mitsubishi. can u tell me the settings & cable for that. I have tried with normal 9pin to 9 pin serial cablewith pin 2---3, 3---2, & 5---5, it's not working. Is there any setting required.
  10. Qj71c24 Serial

    HI, I am trying to do serial communication between PC & MITSUBISHI QJ71C24 serial communication Module . I have done the setting in GX DEVELOPER, but it is not working. There is not much help available in English. Pls .tell me the settings.
  11. Mitsubishi Qj71e71

    HI, I am trying to do ethernet communication between PC & MITSUBISHI QJ71E71 Ethernet Module .I am using Q02HCPU (Q SERIES).I have settedThe IP ADDRESS 1for PLC:10.91.54.79. & for PC:10.91.54.218 sub:255.255.255.0.But I am unable to ping it from PC. Pls. tell me the other settings required.
  12. KEPServerEx SERVER

    HI, In the KEPServerEx SERVER, in DEVICE ID setting thet have mentioned to give IP ADDR.:PC No. Can any body tell me what is that PC No. I am using A3A Mitsubishi PLC with ethernet module AJ71E71.
  13. AJ71E71 ETHERNET

    can anybody tell me , As we have to use TO/FROM instructions to data transfer between PLC & EJ71E71, is it possible to access PLC DATA using this ETHERNET. If yes please tell me the settings in "TRANSFER SETUP".
  14. MITSUBISHI AJ71E71 ETHERNET COMMUNICATION

    thanks for the help. But ihave already tried that, With "transfer setup" parametrers, I am giving a IP 10.91.54.79 & port addr. of 100H. it is pinging from the Copmuter but the ping test from GX DEVELOPER IS not working.