Bryll

MrPLC Member
  • Content count

    349
  • Joined

  • Last visited

Community Reputation

31 Excellent

1 Follower

About Bryll

  • Rank
    Sparky

Profile Information

  • Gender
  • Country Sweden
  • Interests Vintage MX, Two Stroke Road Bikes
  1. I need to use a S7 1214 PLC and connect to two different IP-addresses. The PLC will be connected to three other 1200 systems on "network 1" collecting data on a Profinet "machine network". Customers DCS is collecting data from the 1214 PLC via Modbus TCP on a separate IP-address. Can I use a CP 1243-1 communication module for the second network or is there a better one? Regards /peter
  2. Hi Bryll.

    I need help to convert GX-IEC Developer program to GX Works 2 please

  3. PLC - FX5U Software - GX Worx 3 (latest ver) I'm currently working on a program where I use a lot of advanced calculations supplied by the customer. He would like to protect his calculations in the software, hence the following question. Is it possible to crack the password if i protect the program blocks ? Kind of stupid question since most things are possible, what I'm really after is: How safe is it, can it be cracked easily ?
  4. E-Designer

    I found the Deif415 (15") panel easy to use and it comes with Windows or Linux installed. We use the Linux version of the panel. Up to five users can be connected at the same time with VNC, no license needed. Three ethernet ports. The Deif panel is a branded Exor panel. We decided to buy from Deif since they are easy to do business with and gives good support. It's not easy to describe the advantages over the GOT, but after a while you'll find the GOT a bit "old and square". Our largest customer used a 6,5" panel earlier, but has now realized that the HMI is the face of the machine, and a beautiful face easily opens locked doors. He won't accept anything smaller than 15" now. Have a look at Exor or Deif 
  5. E-Designer

    I have the same E-Designer version as you and it runs on a Windows 7 Pro 64 bit machine. Generally is everything working as intended, but sometimes can't I open the alarms window in the project. A reboot is the cure for that most times. Also a strange behavior of the cursor as you describe it, but only when I try to edit a previously defined alarm. We tried some Beijer iX and x2 panels and also the Mitsubishi GOT series instead of the E-1000 series. But finally did we find a panel we liked, it is a Deif 400 series, it's a branded Exor operator panel.
  6. SER Intsruction Help

      From the manual: FX3 Series Programming Manual page 399 (link)
  7. CRC (check sum with GOC)

    It seems to be a product for the market in India. What software do you use to program it ? Does it support structured text ?
  8. Integer to Byte

    Take a look at the WTOB instruction, it's quite handy but then you need to convert your integer to word format
  9. Mitsubishi E1043 data download

    @Ron_S I think you mean the old CAB-5, but that was used for the E100 series. The easiest cable to use is the Ethernet cable for the E1000 series. It must be a crossed cable if it's a direct connection between the pc and panel.
  10. FX2N 4DA output

    What are you using to enable the TO function ? Is your code similar to this ? -| M8002 |---------------------------------------[TO K0 K0 H0 K1]- -| M8000 |---------------------------------------[TO K0 K1 D70 K4]-
  11. Division a unsigned WORD

    "Word_1 := Word_2 / 16#0A;" works fine for me when deviding Word_2 by 10 (16#0A)
  12. Perhaps a stupid question, but do you have 24VDC supplied to your FX2N-4AD ?
  13. BEIJER E1101 TO MITSUBISHI GOT 2710

    Contact your Mitsubishi dealer, they should have a converting software they use. You have to send them your E1000 project and you receive it converted to GOT format. Just be aware that you need to correct some things the converter can't handle. Good luck
  14. GX IEC Developer, can't open any project

    I'm running GX IEC Dev on my computer without any problem at all. But I had a similar situation what you describe with another programming software. That was a Windows update giving me problem. Just uninstall the Windows upgrade and it worked again. I'm running W7 on my laptop and had some issues lately with some programs due to Windows. Latest version of GX Works 3 won't open any project on my laptop, don't know why at the moment but the support is notified.