Search the Community

Showing results for tags 'wiring'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 9 results

  1. Keyence / proface

    Good dat i have a trouble of having this errors.  Can i ask also a wiring config for keyence kz a500 to Pro face GP4301tw  Thanks in advance 
  2. Connected Components Workbench

    First time using Connected Components Workbench and am modifying an existing program,  does anyone know why and how the original IO_EM_DI_ numbers have been changed and not just the alias'. When I right click and select properties for each tag it gives the address and says 'Read only cell' generated by the I/O wiring tool indicating the I/O channel to which the variable is wired' Any help would be great thanks!
  3. Hello, -I'm considering using an AB 1734-IB8 to count input pulses from a Micro Motion flow meter transmitter and, since I'm very new to this stuff, would like a little guidance as to how/if this can be done.       My first concern is the wiring. The manual for the transmitter shows this wiring diagram for the specific model I'm using.       Here, B would represent the 1734-IB8 module. I'm not going to be using the analog loop. In addition to this wiring, terminals 9 & 10 on the transmitter will be wired to the same 24V and Common as my PLC modules.        The 1734-IB8 manual shows this diagram for wiring.       Should I consider the pulse output of the transmitter as a 3-wire device, connect terminal 3 of the transmitter to my 1734-IB8 input terminal and disregard the connection from terminal 4 of the transmitter, or should I just tie terminal 4 to my common? Or, Should I consider my pulse output as a 2-wire device, tie terminal 3 of the transmitter to my 24V and terminal 4 to my input module? My guess is the pulse output should be considered a 3-wire device with terminal 4 of the transmitter tied to my common, but I'd like a little bit of explanation with this. -My second main concern has to do with the capability of the 1734-IB8 module to read pulses. More specifically, I would like to know what parameters of the module I need to research to see if it will be possible to read the pulses from my transmitter in the application I'm considering. If the 1734-IB8 can't be used, I would end up going to a high-speed counter card.   Thanks  
  4. Hello, I have a cp1h-y20dt-d (sinking output) plc supposedly to be wired to a servo controller. The pulse control method is Pulse/Direction. I've did some manual research on the PLC and found the following diagram attached Untitled. Since the diagram above doesnt show which terminals does it connect to in the CP1H side circled red, I want to ask if those connections belong to the following diagram attached Untitled1? If so, assuming im planning to use only Pulse Output1 (Pulse/Direction method) from the PLC side, is the connection from the first diagram no.1=CCW0- , no.2=CCW1- , no.3=COM (connected to -ve) *Note: these diagrams are from omron's manual SYSMAC CP Series CP1H-X40D_-_ CP1H-XA40D_-_ CP1H-Y20DT-D CP1H CPU Unit Your replies would greatly help. Thanks and best regards, Summer
  5. Analog Wiring

    I need to connect a analog amplifier with the analog input 0-10V on my Siemens 1200 PLC (located inside the same cabinet as plc, about 40 cm between). do i need a shelded cable? or just RK0,75mm2? do i use any special color on 0-10V?
  6. Trouble Wiring a Simple LED with a Micro820 Controller

    Hi everyone, Recently, I started working with the Micro820 Controller Embedded I/O. My project is simple : when the output _IO_EM_DO_00 is set to true, an LED light turns on. But, even though it's super simple, I can't make it work. Here's my setup. If you need more information, feel free to ask anything !
  7. Hi,I am new in project engineering and my previous work is PLC programming only. For experienced engineers, what are the step by step procedure that you use in migrating/upgrading and what are the things that I will avoid?
  8. widadi

    does anyone can help how to connect plc fx2n-16mt with servo drive mr-j2s-40 and motor servo hc-kfs-43 ? please give me wiring schematic thanks a lot
  9. I wonder if anyone can recommend cable id printer? I know Brady is the leader in this field and I have used their products in the past but I wonder if anyone has used any other manufacturer they can comment on? I found the K-Sun Green Machine but I am not sure how does it compare to lets say Brady BMP71 and how much more expensive or cheaper their consumables are? Any other products worth mentioning?