Search the Community

Showing results for tags 'servo over load setting'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 57 results

  1. Hi,  I want to use the servo drive in internally speed control, how can I change the motor direction? Do you help me for wiring and parameter settings please.  
  2. hello everyone,,,, I want to running the motor in 100 rpm but how to setting electronic gear to control speed in servo motor HG-SR502,, does anyone know how?
  3. hallo everyone ...i use mitsubishi Q00UJCPU and QD77MS2.. i try to make a speed control program and the speed wants to be changed during servo operating, i use dedicated instructions ZP. PSTRT1 (axis 1) and have tryed but it was only successful to change speed with "change speed control" function once ... is it like it? cannot change "change speed control" many times when servo operations?
  4. hallo all, I want to ask if I click "read PLC Data" the "points" will appear, I use the QY18A output module that uses 8 points but there is no choice, the smallest is only 16 points.  so I can't put 148 in the "start XY" column ... will it affect the I / O address in the program?
  5. Is there a way to monitor the Temperature of a Servo Motor on Allen Bradley Servo motors... MPL? PLC: CompactLogix 1769-L30ERM Drive: Kinetix 6500   Motors: MPL-B310P-MJ72AA, and  MPL-B560F-MJ72AA I would like to be able to monitor the temperature, and flash a warning screen on the HMI if the Motor gets too hot, or perhaps shut down the operation before the Motor overload trips. The drive and PLC are connected through Ethernet IP What I don’t know is if that Motor heatsink temperature information is available to the PLC.
  6. Hi All, I am doing an application that use servo motor to feed plastic film to a target length (set by operator), and it need to stop immediately if marker sensor is ON. This application is control by Omron CP1E PLC. It will feed plastic film in 500-1000mm/s depends on the target length set by operator. It is require to stop immediately if the servo feed length more than 90% of the target length and the marker sensor is ON. However, is there any possibility for the servo to stop immediately once the condition is meet? As I am using PLS2(887) to feed with target length, and INI(880) to stop immediately, however, it cannot get the desired result as servo not able to stop immediately after marker sensor is ON, I am not sure is because of the PLC scan time, or servo need time to deceleration (deceleration rate assigned to #FFFF). Appreciate anyone able to assist on this. Thank you.
  7. CC-Link IE + C#

    We have a controller written in C# and need to integrate a servo.  We are looking at the Mitsubishi servo MR-J4 line.  Unfortunately it doesn't support Modbus TCP but does have the CC-Link IE protocol.  Does anybody know if it is possible to talk to CC-Link IE via C#?   I'm having a helluva time trying to find an answer.  I see some thing about Seamless Message Protocol (SLMP) and CC-Link but the info is somewhat sporadic.  Any advice is much appreciated as I've never worked with the Mitsubishi product line (but interested in their PLCs).
  8.  Hi all. I have a question about how to set up the motor in rotary mode. My application will be a basic rotary table driven by a servo motor without gearbox between. So, in my servo drive axis settings, I select the motor as a rotary mode. then I defined the maximum position setting value for 360 degrees, and minimum to 0. So far so good. But the problem comes when I want to make an absolute move using the mc_moveAbsolute to move 360 degrees. Whit this settings the error "target position settings out of range " will come up. So, what is the solution to rotate 360 degrees without generating this error? if I set up the maximum value to 361 degrees and then if I rotate 360 the error will not occur and the motor will rotate 360 degrees as I aspected, but it's this correct ? or there is another way to do it? Thanks  
  9. Kinetix 300 servo drive

    Is there a real-time help resource for this thing other than the worthless AB site, on which the support page has been giving an error message for 2 weeks?
  10. Hello everyone! I have problem with understanding the usage/principle of operation of parameter "Mark detection number".  In manual i read: "The number of mark detections is stored. "0" clear is executed at power supply ON. Continuous detection mode: 0 to 65535 (Ring counter) Specified number of detection mode: 0 to 32 Ring buffer mode: 0 to (number of buffers - 1) Refresh cycle: At mark detection" My question is which mark detections are stored? Servo detects some kind of marks? I am novice in servo programming, please explain in the easiest way. Thanks for help.
  11. Servo Motor Connection

    Hello, I am using the R88M-1M40030T-BS2 ( 200V 3ph) servo motor. I am looking for a diagram that explains the connections on the top of motor ( for power supply).. there are more than 3 pins and i am not sure why. Can anyone help me understand the pins on the motor for the 3ph supply?  Thank you 
  12. Posted 22 July · Report post Dear Friends,       I want to set my servo controller overload setting as per my machine load requirement since all my servo installed in my machine over travelling and hitting trying to run continuously which is resulting servo failures ,repeated timing belt cut issues.Kindly help me resolve this issue.since i am not familiar with servo controllers.Model used A5 II minas servo MADKT 1507 and contol mode in position control setting.
  13. Dear Friends,       I want to set my servo controller overload setting as per my machine load requirement since all my servo installed in my machine over travelling and hitting trying to run continuously which is resulting servo failures ,repeated timing belt cut issues.Kindly help me resolve this issue.since i am not familiar with servo controllers.Model used A5 II minas servo MADKT 1507 and contol mode in position control setting.    
  14. Hi, I am trying to do a merge move on 1S Servo. The condition are as follows: Task: Move 2 in(absolute value) and then Move back to 1 in (absolute value). I have to do this move 10 times in a row.  The application is material leveling after dumping in the mold. The only question i have is if I use just MC_MoveAbsolute command, the only buffer mode for transition available is velocity. Is there a way i can do it with position. I dont want to stop when I can go from 1 to 2 and 2 to 1 again and again. Its time consuming. But rather a nice oscillation motion without stopping to mimic leveling. Can anybody please help me out with this problem.   Thanks
  15. Hi, I'm trying to set up PLC (CJ1G) to control servo motor. I'm using position control unit CJ1W-NC413, servo relay unit XW2B-40J6-2B and smartstep R7D-AP02H servo drive. I'm reading through manuals and feels little overwhelmed with information. Everything is probably there, but it's going to take lot of effort to put it together. Can I found example program somewhere? EDIT: When I put jumper to pin 25 (X axis RUN), motor shaft is locked and motor is holding position, so wiring should be correct. When I try to run a program, I can see that parameters are changing in CX-position, but servo is not moving. Please see attached picture
  16. load cell SP4M-7Kg

    Hello guys, I have a system of 3 load cells (SP4M-7Kg) attached  to a Micrologix 1500 analog inputs. in the same PLC i have 3 coils for a vibrator, each vibrator is working with signal generators. and the load cells with an external 24vdc Power Supply. i see my load cells readings fluctuating too much even with the vibrator not working. if it is set lets say 70 Grams it is jumping from 68.4 to 74.8 going up an down never never stabilizes in one number, so i suspect am getting noise somewhere put a 100uF capacitor PLC inputs for the load cells but weight just increases more and more. How can realize where is the noise comming? what can i use as a filter? how can i improve this system? should i changed it to digital?   any help welcome! thanks.  questions?    
  17. Homing servo motors

    Hello everybody, I have a question about homing servo motors. I have a project with new servos from Omron and I would like to know what is the best way to do homing for the servos and how often. Before when we have servos with encoders I was making special homing sequence and was calling by some event. I heard that new servos from Omron pretty smart and remember own position without batteries. So with this 'new generation' of servos what is the key to keep machine robust, easy for motor replacement without useless programming stuff. Regards, Scotty
  18. Is there a way to change the parameter of a mitsubishi mr-j3a using fx3u plc?  Need this to change the pulse output of a master servo amp to change the pitch of the other slave servo amplifier. 
  19. I am trying to connect a Delta ASDA-A2 Servo internal motor encoder to a Delta DVP28SV high speed counter input.  I was successful in connecting the servo to the plc on position mode with an external encoder connected to PLC high speed counter.  Currently having trouble in finding the correct wiring between the servo drive and the plc to count the pulses from the internal motor encoder.  Attached are some figures from the servo drive manual. OA --> X0 is obvious, tried s/s to GND, COM-, VCC and VDD... no result. Any suggestion would be highly appreciated.  
  20. RS logix 5000 motion control

    Hi Guys! I have a problem with Motion axis move (MAM) command. There is an Allen bradley servo motor what is working well. But I need to add a new program section, wich is in  a specified moment, the axis should move a certain distance. I think I need to use the mam command, just I dont know how can I configure the motion control part. I need to make a new tag ? or what ? I need to use a user define ? PLS help me.   
  21. Gx Works 2 ve fx2n için bir fonksiyon kütüphanesine ihtiyacım var. Servo ve step motor kontrolü için.   thank you
  22. Hello, I have a cp1h-y20dt-d (sinking output) plc supposedly to be wired to a servo controller. The pulse control method is Pulse/Direction. I've did some manual research on the PLC and found the following diagram attached Untitled. Since the diagram above doesnt show which terminals does it connect to in the CP1H side circled red, I want to ask if those connections belong to the following diagram attached Untitled1? If so, assuming im planning to use only Pulse Output1 (Pulse/Direction method) from the PLC side, is the connection from the first diagram no.1=CCW0- , no.2=CCW1- , no.3=COM (connected to -ve) *Note: these diagrams are from omron's manual SYSMAC CP Series CP1H-X40D_-_ CP1H-XA40D_-_ CP1H-Y20DT-D CP1H CPU Unit Your replies would greatly help. Thanks and best regards, Summer
  23. ab

    The HMI server in area 'RNA://$Local/Spring_Insertion' refused to load it's project. The HMI server is not licened and cannot open a project with more than 5 displays
  24. Logix 5000, Array filling

    Hi there! I have a question with AB PLC. My problem:  I have some raw data...distance for example.When the machine starts,the sensor begins to send the information with the distance values. When data is received it is moved into an array. After the first 5 values the program calculates an average and the result is moved into another array.Currently after receiving the fifth value,thus filling the first array,making the calculation and sending the average to the other array,the program empties the entire first array instead of just always discarding the oldest value of the five,and recalculating the average with the newly arrived value every time. I tried to made this with ladder diagram using an an fifo load and unload but isnt working. Please help me if anybody can. Thank You.
  25. mrj4

    hi all, anyone can hep..i use servo mr j4.. now got error 121..anything can help..i read from manual error code but cannot understand..