Search the Community

Showing results for tags 'master salave configuration'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 49 results

  1. Hi all, I am working on a safety PLC conversion project, for which I need to identify the input word address configured on a PSS AI IP card. The manual from the official website shows the address configuration via a DOS tool. I do have PSS SW PG WIN 4.9, but the project file has been created with PSS WinPro 2.3. Within this software there is only the option to configure how the input channel behaves, not which input word is used (see attached screen grab). Anyone with a distant memory if the addresses can be set with PSS WinPro?  
  2. Hi, About SmartSlice: „Smart Analog I/O performs data pre-processing to help you reduce PLC programming. Scaling and alarms, and even totalising or rate-of-change calculations are handled inside the unit.” How to get to this honey in case of GRT1-ECT bus coupler and NJ101 EtherCAT communication? What means “Configuration Tool” in W18E-EN-02 “GRT1-series EtherCAT Communication Unit Operation Manual”?
  3. Hi everyone, I have a question for you all, Is possible to configure CJ2M-CPU11 with tags trough network configurator to connect Control Logix PLC using EthernetIP? I did a configuration with CJ2M-CPU31 and Control Logix PLC with no problem, but now I need to communicate CJ2M-CPU11 with Control Logix PLC using EthernetIP. Some of you did this configuration between this two PLC before? Regards!
  4. RJ71EIP91 Configuration mismatch

    I have several machines that use the RJ71EIP91 module. I have not had any issues until now. I do not have the original apa file. I upload the configuration and try to restore it from the configuration.apa file, it does not show everything that is connected to the card or programmed in the PLC. when I verify this it says that the configuration is a mismatch. I have several of these scattered throughout the factory and I don't have this problem anywhere else. Is there a solution to this problem?
  5. Hi All, I just start to setup a rotary servo (rotary transmission load type) and the designer pass me the spec of gear ratio 1:100. In my motion scaling page, I set Transmission I:O as 1:100  and then scaling unit is just position unit with 1:1. However, when i jog my rotary servo, it does not reflect the actual position in degree, so I went to read through the manual but still cant quite get how should i configure my scaling so that I can see that when the motor is rotating, i can see it rotate how many degrees? I try to set scaling 360 degree to 1.0 load rev, and the position feedback seems like much more finer....
  6. Modbus/TCP Client Driver for .NET 6, .NET 5 & .NET Core. - ASComm IoT View File ASComm IoT for .NET 6.0, .NET 5.0 & .NET Core developers. Class library for use in Visual Studio.NET to create HMI/SCADA apps that communicate with Modbus/TCP Server devices via Ethernet. Does not require OPC or 3rd party drivers Visual Studio.NET 2017, 2019 and 2022 compatible All .NET 6.0, .NET 5.0 & .NET Core targets are supported, including Web, Windows, console, and service apps. Runs on Windows, Linux & Android Extremely high performance - 5~10 mSec typical transaction time Supports Modbus functions 1, 2, 3, 4, 5, 6, 7, 11, 12, 15, 16, 17, 20, 21, and 24 Address mode support includes: Zero-based, One-based, Modicon 5-digit (1, 10001, 30001, 40001), Modicon 6-digit (1, 100001, 300001, 400001) Abstract base classes allow you to write generic code that works with all drivers Synchronous and asynchronous read/write methods Data change notifications Provides common user interface across all driver classes No limit on number of devices or data points Multi-threaded for high data throughput Includes extensive help system Example applications with VB and C# source code included. Easily connect office systems to factory floor. Runtime-free for qualified applications Submitter Automated Solutions Submitted 05/18/22 Category Demo Software
  7. Version 1.4.0

    34 downloads

    ASComm IoT for .NET 7.0, 6.0, 5.0 & .NET Core developers. Class library for use in Visual Studio.NET to create HMI/SCADA apps that communicate with Modbus/TCP Server devices via Ethernet.  Does not require OPC or 3rd party drivers Visual Studio.NET 2017, 2019 and 2022 compatible All .NET 7.0, .NET 6.0, .NET 5.0 & .NET Core 3.1+ targets are supported, including Web, Windows, console, and service apps. Runs on Windows, Linux & Android Extremely high performance - 5~10 mSec typical transaction time Supports Modbus functions 1, 2, 3, 4, 5, 6, 7, 11, 12, 15, 16, 17, 20, 21, and 24 Address mode support includes: Zero-based, One-based, Modicon 5-digit (1, 10001, 30001, 40001), Modicon 6-digit (1, 100001, 300001, 400001) Abstract base classes allow you to write generic code that works with all drivers Synchronous and asynchronous read/write methods Data change notifications Provides common user interface across all driver classes No limit on number of devices or data points Multi-threaded for high data throughput Includes extensive help system Example applications with VB and C# source code included. Easily connect office systems to factory floor. Runtime-free for qualified applications
  8. Hello! I am working on a quote for a new project that will use EtherCAT but also requires DeviceNet for some legacy components.  Has anyone successfully used the Beckhoff EtherCAT coupler (EK1100) with the DeviceNet Master Terminal (EL6752) and an Omron PLC as the EtherCAT master? My concern is that the coupler will only communicate with the Beckhoff EtherCAT master, but since it is so much more expensive to get the new Omron parts to communicate DeviceNET i am hoping this could be an option.  The equipment is extremely simple and price is a major consideration.   Thank you!!!
  9. KINCO PLC as MODBUS RTU slave

    Hello to everyone. I hope you are doing well. I'm trying to establish a communication between my PC and my KINCO PLC. The manual states it supports MODBUS RTU protocol, so I downloaded two different Modbus Master simulator I found out: Multiway from OMRON and qModMaster. None of them seem to work properly. I attached some pictures of the messages I get. https://ibb.co/f1mCSNt Multiway message https://ibb.co/bP5cX1t qModMaster message I include the configuration of the communication parameters. https://ibb.co/nMty8D9 PLC parameters https://ibb.co/6RTqVfC Multiway parameters https://ibb.co/N1XTccd qModMaster parameters According to the manual, in order to play the role of Modbus master with the PLC it's necessary to configure some instruction blocks (I'm programming in ladder). However, I could not find any block to configure as Modbus slave. I don't know what else I can do. I'm in trouble with this task. Am I making some mistake? Thanks for your attention.  Kind regards!
  10. Is there a way to run a compact logix program, while ignoring the the I/O configuration?   I used to do this with other PLC's to help develop the HMI screens while connected to development PLC that does not have the full complement of cards that the end user PLC will have.  Just lets me test logic that supports the HMI while working at home.   I used to do this on other PLC's with just a CPU on my desk.   Possible?
  11. Hello guys, I have an application with a Delta PLC (slave), Load cell module and Delta HMI.  The problem is that the Delta PLC has to report to the already existing platform of Siemens S7 PLC (Master) with Profibus. The Master (Siemens) writes and reads data from the Delta PLC. The question is, how can I set up the Profibus communication? Are there any documentations about the Memory Mapping, configuration etc. There are some modules for Profibus Slave from Delta but I cannot find any references or anything. Thanks in advance.
  12. We have a customer insisting on communicating with our NX102-9000 over EtherCAT, we have explained multiple times that EtherCAT is not intended as a facility communication protocol and recommended that instead they use Ethernet/IP, but after a year of pushing back they are still insisting and willing to pay for the Engineering work to get this to happen. Has anyone successfully configured two EtherCAT masters to communicate with each other? In the past I have used the PN-PN Master Coupler from Siemens to get two ProfiNet Masters to communicate with each other so I am hopeful that a similar device exists for EtherCAT, but I have not had any luck searching the web for such a device. Does anyone have experience with or know of such a device? Thank you!!
  13. Thesis idea

    Hi guys!   Actually, I am student. I need to choose a thesis topic soon. I would like to write something which is connected with automation. I wolud like to ask your help, to figuring out an idea, what can be a good topic in nowdays. It would be a master degree already. Im using AB PLC-s, so it would be convinent if someone could suggest for me what I can solve with this, enviroment (rs logix 5000, studio 5000) Im not asking a solved thing. I would like to ask some ideas or tip. If anyone have some idea, pls share it thanks.  Thanks in advance.
  14. Simatic pc to simple pc with profibus card

    Hi every one, One of my machine i have to fix , has simatic pc unit installed that causing too much trouble  and client want to replace it with simple pc with additional profibus card installed in PCI slot, is there any way to configure image of simatic pc in new simple pc
  15. Hi, I've got a very old version of Wonderware, version 9.5, which isn't going to be upgraded anytime soon. I would like to configure a button to perform 2 tasks under "Touch Pushbuttons", ideally "Action" and "Show Window". I am unable to enable both at the same time, so I've been trying to write a script that would perform both functions, but so far unsuccessfully. Is this something that can be done, or is there another way to get around this problem? I would like the button to toggle a bit and to open another window with more controls.   thanks
  16. Hello,  I want to compare pulsed coming from flow meter with a constant value. And make a bit to high level when my set pulses are equal to present value in counter. I am using 1734 Vhsc24 module for this. If any body have sample program kindly attach it. 
  17. Hello All,  Am a bit new to practical PLC applications. I was trying to configure a Phoenix Contact I/O module (1452916) on a MicroLogix 1100 PLC but it kept faulting out with the fault light RED. It would say "Major Error Halt S:1/13". The error description says I/O mismatch. The error code is 187h (see attachment). The Phoenix module has a cable with 19 pin positions for the 8 input. I connected the pin 17 and 18 to 24 volts and  0 volts respectively. Then because I was using input 5 I connected the pink wire to PLC input (I/1) 24volts and the White/Yellow wire to the PLC common.  On the I/O configuration on RSLogix 500, I used "Other" ( See attachment) but did not know the vendor details. Could anyone help me with the steps on how to communicate with the module? I have also attached the PLC program I was running. Thanks        
  18. Hello, I have been so many days trying to comunicate the multiway software trought a serial usb converter with the SCU31 device, using a omron function block to read a holding register, but I can't achieved it. Now Im receiving some frames on multiway, but there is always some errors. I was wondering if somebody in here that have worked previously with modbus and omron can be able to help me in how to configure everything corectly to be able to read the value from multiway, on the plc, and where is this value saved.  I'll upload some captures to show what I have done till now.    
  19. Q06UDEHCPU MELSECQ Upload

    Hello ,  I dont have experience with Mitsubishi PLC.  I want to do a modification on the ethernet configuration but i dont have the source code .  According the information that i read we can use GX IEC developer or GX developer but my question are :  Can i upload and download the program with GX developer?  Even if was previous developed with GX IEC Developer i will not do any change on the code only on ethernet configurations , add a MC communication. I have another concern about the profibus module. For the profibus is necessary another program right ? But if i don't want do any modification on the profibus is dont need it, right?  My experience on Siemens when is necessary do a modification on the hardware configuration. I should have all the hadware configuration " right"  it means if i have profibus i should have the right GSD to allow do modification on the configuration .  But on Mitsubish i can´t understand that well . Regards  Roberto Fonte  
  20. BECKHOFF CX-9020

    Hello PLC experts, I am master student currently writing thesis. For this, I have a initial task of making some changes to PLC program (Just started getting to know about PLCs- complete beginner). I have a BECKHOFF cx 9020 PLC connected to my notebook using ethernet. I am using TWINCAT 3.1 (VS) as IDE. Firstly, I cannot find my PLC IP address connected to my notebook . I added the route in the Twincat and it shows the PLC is connected. When, I am trying to run a program (activate boot project), I am unable to login to the PLC. It gives an error "login failed for application port 851". What I undertood from BECKHOFF scripts,  there is something wrong with the ADS ams net ID which I am trying to figure it out. I appreciate all the help. Thank you.
  21. Is it possible to use FX3U-485ADP-MB as a serial port to send and receive user defined string/data to and from a computer? I have a FX3U-32M PLC and two FX3U-485ADP-MB adapters. I have been using PLC with one adapter as Modbus Master. Now i want to use both adapters, where one will be Modbus Master as usual and the other I want to use to send and receive data to and from computer terminal (Example - Realterm). I have a third party 232/485 converter which works really well. Lets me just describe my requirement straight forward. I want to display process parameters on a windows computer based user interface (UI) and also set some variables in PLC from the same UI. The UI has access to serial ports of computer.
  22. hello.   I've been trying to communicate this omron plc CP1L-EM30DT1-D, with a yaskawa inverter cimr-vu4a0004faa. but i can't figure out how to make de correct mov or configuration in de DM. i need to run/stop, change frequency.    some help, please. :) 485PRUEBA.cxp 485PRUEBA.opt
  23. Hello I have a scenario that's been bugging me for some time now. The scenario consists of a Micrologix 1400 that I need to control it's output from modbus/tcp. In detail what I really need is to be able to manipulate the O0:0 through modbus/tcp. The PLC would be the master and I would be the slave that triggers the connection to the master. I'm using a Modbus-Client on my PC and that should be the slave. Any idea as to how I can manage that? Currently I can send data to the master but everything is "stored" on B10 and I have no idea how I could write directly on O0. Thanks a bunch guys. PS: I'm borderline noob. 
  24. Hello all. I have been working with an SLC 5/04 system, which houses various Digital and Analog INs and OUTs, up to Slot 29. I am currently mainly working with Slot 25, an Analog Input: 1746-NI16I. This is a system which has already been set up and has been running for the best part of 8-10 years. This particular card has had some spare inputs, one of which I am trying to connect to. In the Advanced Configuration, only a few Channels are actually "Enabled", and each channel is pretty much slightly different from another in terms of Input Type, Filter Frequency and Data Format. I am trying to set up Input 14, which is Channel 15, to "Enable" it, 4-20mA Input Type, Filter Frequency of 6 Hz and Data Format of either Raw/Proportional or Engineering Units. Now, after I have made my choices, I click apply, and then OK. I am then confronted by a pop-up which states: "Configuration Rung and Data Integer Data File Number: 25 Integer Data Element: 100 Rung to be inserted: XIC S2:1/15 COP #N25:100 #O0:25.0 24 At Program File Number: 4 82" I have the options of OK or Cancel. If I click OK, I now have LAD 4, Rung 82 Highlighted. This First Scan Bit and COP function were already here, but does that mean I have now altered what is being written to "#O:25.0"? I now Download the Changes. However, after all this, I am not getting any Analog input reading coming in from the Live PLC. What is this COP function? What does it do? How do I properly set up this Analog Card?   Thanks for your time, -Jame
  25. Password Protected LS Master K

    I have a customer that has a LS Master K PLC, and he needs me to make some changes to the program. I am not the original program writer so I do not have the original program nor the password. And the company that originally made this program does not exist anymore. Does anyone have any suggestions on a software or a device that can help me either find the password or just bypass it. I need help ASAP Please!!!!! I saw there is a password breaker while i was googling, but the software cost $50, and it looked a little sketchy so I am kind of hesitant to trust 1 purchasing the software and 2 downloading it only my work laptop. Please help!!