Search the Community

Showing results for tags 'intelligent device'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 9 results

  1. Hey everyone! New member here, and this site has always been a big help!  I try to help other folks too, but a lot of guys are super quick on here.   I've got a problem using some obscure components. I inherited a sensor network at work that uses Panasonic S-Link and I need to read them from a Q-Series. Panasonic makes a module that slots into the Q Series called an SL-VMEL-Q that I have.   My question is:  Did I do everything correctly on my Mitsubishi side? I put it into the parameters as an intelligent module with 64 points and I put the correct address in for the start I/O. Is that all I have to do?  This is the first time I used a module that wasn't on the drop down list when you add one in GX Works 2.   I can read and write to the buffer memory, but I can't get the unit to send to or receive from the sensors. I think the problem is that there is no end unit on the S-Link line (I don't know if it's just a terminating resistor or what), but it previously worked without one, so I can't be certain.
  2. GX Works 2

    Hello everyone! Can anyone suggest to take all the Input and Output (digital) status at a time in a single file for backup in gx works2 in FX2N PLC. I need to confirm that all required IO are in perfect condition before start operating the machine. Also I plan to design a troubleshooter to find problem.
  3. GX Works 2

    Hello everyone! Can anyone suggest to take all the Input and Output (digital) status at a time in a single file for backup in gx works2 in FX2N PLC. I need to confirm that all required IO are in perfect condition before start operating the machine. Also I plan to design a troubleshooter to find problem. Thanks in Advance..
  4. I am searching for the Replacement of the Ultra 5000 Servo Drive as i cant get online to it with the Ultraware software over wireless plant network. In order to get online i have to connect serial cable every time. And the Drives are used in time critical assembly line  kind of environment. So is there any other replacement which works as intelligent as of Ultra 5000 and also have additional feature of built in Ethernet port which can help me to get online with it wireless over plant network.
  5. HI Everyone,  Recently i have bought a plc fx3ge and gt2000 hmi .the problem is that whenever i use a device address d280.b1 in hmi .i am not able to use the same address in gx works for plc (LD D280.1).can anyone help me with this problem.   
  6. GOT1000&CompactLogix Tags

    Hello Im new using HMI got1000, Im trying to connect using Ethernet this HMI to a compactlogix, i already imported the tags, but i can't use any of them, because the gtworks3 says "you have to map the tags for set a device", i dont know what means map the tags, some one can help me please?
  7. PAROCK1 for HMI/SCADA View File Now a software solution is available for your Modbus (MB) needs in Rockwell/Allen-Bradley Control Logix or Compact Logix (Clgx) family processors, instead of a traditional 3rd party hardware like Prosoft MVI-56, Molex SST-SR4-CLX-RLL etc.  It is an Add-on instruction (AOI) for PLC/PAC firmware v16 or later, (other solutions are available for pre v16 systems).  For hardware interface, use PLC’s channel 0 (serial) or TCP/IP Interface module(s) to have as many MB TCP/IP devices or serial devices.  (Some limits apply based on system configurations, Comm. settings depending on HW used.) Connect any MB Client/Master or Server/Slave device(s) to your CLgx PLC, including flow computers, analyzers, VFDs, Power Monitors, Level gauges, Smart I/O, etc.  All the MB public/native function codes are supported.  32-Bit integers/floats as single entity are supported with byte and word level swapping. A separate utility automates the data mapping to your PLC logic.  Features -Serial Master (BASIC required Option); TCP; Slave; Redundancy; More than 5000 accumulative registers; MB CFC (Custom/Private Function Code) Support; Data mapping too – Between PAROCK1 & your PLC logic; Packaged with Rockwell; TCP/IP Interface Module; Volume Discounts; Annual Support Requirements -Rockwell/AB-CLgx processor with v16 or later.  Contact PCI for earlier versions. -If using CPU’s Chan0, you cannot use Chan0 for any other user mode activity. You can use it for non-user mode activities -TCP/IP Interface Modules from Rockwell/AB supported, are: -1756-EN2xx ControlLogix® Ethernet/IP communication modules, firmware revision 5.007 or later -1756-EWEB ControlLogix Ethernet/IP web server module, firmware revision 4.006 or later -1768-EWEB CompactLogix Ethernet/IP web server module, firmware revision 1.002 or later -1769-L30ER, 1769-L30ERM, 1769-L30ER-NSE, 1769-L33ER, 1769-L33ERM, and 1769-L36ERM CompactLogix controllers, firmware revision 20.011 or later -1769-L24ER-QB1B, 1769-L24ER-QBFC1B, 1769-L27ERM-QBFC1B CompactLogix controllers, firmware revision 20.011 or later -1769-L16ER, 1769-L18ER, 1769-L18ERM CompactLogix controllers, firmware revision 20.011 or later Other Related Services/Items -Custom PLC Add-on instructions building -PLC upgrades, troubleshooting, applications -PC Windows, iOS5, Linux, Mobile devices Comm. Drivers -Custom development, Technology Transfer Services  -Other Non-AB communication drivers for serial or TCP  -Full control system integration, training, architecture design This driver can be conviniently used with Visual Studio in development of complete large scale complex HMI/SCADA Systems. It can be used to perform advanced reporting MES, analytics, IoT, Big data type apps. One example is available to download here For More Info Overview of Parijat Drivers: Click here  Additional supporting Info about Parijat Drivers:Click here Complete Related Driver options: Click here     Submitter Scadadoctor Submitted 03/10/16 Category Other PLC Demo Software
  8. Rotary input device

    I am looking for some sort of rotary input device which could be used for fine adjustment. Ideally it would have to two output pins, if turned clockwise it would send pulses on one of the pins and when turned counterclockwise it would sent pulses on the other pin. These could be connected to two inputs on PLC and a value in a given variable could be incremented and decremented depending on the direction of rotation. Almost like using potentiometer with analog signal. I guess if I can not find anything I could use incremental encoder and look at the phase of the output to decide which way it is being turned but hopefully simpler and maybe more cost effective solution is out there? Thanks.
  9. I am trying to find a way to do a "batch monitor of Global Labels" in Mitsubishi GX Works2 Software. I can monitor Device/Buffer Memory Batch but can't find a way to monitor all Global Label's status online? Can anybody help me on this?