Search the Community

Showing results for tags 'fx1n'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 7 results

  1. Hi I'm trying to figure out how to use the OP320-A to control the relays on the FX1N-20MR. I have mastered the OP edit tool, but I havn't learnt how to use GX Developer. The FX3U and op320 by 485 setting youtube is a good start. Does anyone have a GX Developer project file available. Is there an OP320 and FX1N or similar that comes together, pre-programmed, ready to use. I know how to write C++ programs to send RS485 commands, but this GX developer looks complicated. many thanks Tim
  2. Hi guys, I've encountered a weird problem backing up my old FX1N-24MR-ES/UL PLCs. Hope I can get some helps here. I'm grateful for all the help. I got some old FX1N-24MR-ES/UL PLCs working on machines, and most of them are working 24/7 for more than 8 years now. There's a computer in machines communicating with PLC via SC-09 harness( RS232 - RS422 ). Since Mitsubishi isn't selling and manufacturing FX1N-24MR-ES/UL anymore, I tried to find some compatible alternatives. I bought a Shihlin Electric AX1N-24MR-ES(It got licensed from Mitsubishi to approve it's 100% compatible with FX1N-24MR-ES/UL) and a copied FX1N-24MR-ES/UL from China. I downloaded and verified programs/parameters into both PLCs via GX Works2(both PLCs shown as Mitsubishi FX1N-24MR in GX Works2), but they both work about 5~10% differently from the original ones on the machines. But it seems the both new PLCs are working identically. I've tried download the original program/parameters to a old original FX1N-24MR-ES/UL and it works well, so it seems the program/parameters I read out is correct. I've also checked the both VRs(D8030, D8031) aren't used in the program. May you please let me know what else I can do or test to make the new PLCs I working 100% identically as the old ones? I'm grateful for all your kindly help guys. Thank you and have a nice day
  3. Connect FX1N-60MR to SCADA

    Hello all! I have a FX1N-60MR. I need to display the contents of their data registers to the SCADA system. If you look at the product catalog, there are a few solutions either install into the slot of the additional equipment interface adapter FX1N-CNV-BD connect the communications adapter FX2NC-ENET-ADP, but this raises the question - what Protocol is used?, either install in the slot of the additional equipment interface adapter FX1N-CNV-BD connect the communication module FX2NC-485ADP, but this raises the same question - what Protocol is used? Whether it is necessary in both cases to modify the program code in the PLC, do I need to configure extra modules? What typical solution to this problem?
  4. I found a blog like this, but have not experienced it yet and it's not entirely clear what it should give out at the output? How does he work? I write through values into variables. Then I just write down the dechki and then I'll change these doshki from poneli. And that's why it's not clear at the exit !? What will be on the way out? I thought that there would be a flag that would start heating up. Previously, I used the developer, but then I began to migrate to Works2 and now I'm stuck with PID. I downloaded a couple of libraries for PID for Works2 but there is something that a lot of everything I do not think that I need all this especially since there for 3d 5g Tell me how you can use this blog only? And can they only be dispensed with? and tell me how you can make help in works2?
  5. Hello, Everyone . Do anyone has experience in FX1N-232-BD connect to GT11 (or other model) from Panasonic ? I try to connect them via RS232 port and I setup parameter following HMI manual but It doesn't work at all only RX led on 232-BD blinking Any suggestion ?    Matcha IMG_39346964.MOV
  6. I have two plc, they are the same but I need to see and transfer the programming of one to the other. How can I do this ? I need a software?  What's? What's I need to do this ? Thanks. 
  7. FX1N PLC ERROR 8067

    Hi everyone, I have a FX1N conected with an HMI Beijer E100. the application is not working, the plc has no error light but the HMI Says: PLC error 8067 any idea what that error means and how to fix it?