Search the Community

Showing results for tags 'download cpm2c'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 28 results

  1. Hi Everyone,I have a customer that needs a CQM1H (CPU51) replaced. They purchased the processor new-old-stock from a source they found online. It arrived in the original packaging and had the safety label around the top of the unit, so it seems that it is as advertised and no need to suspect that it would have problems. I purchased secondhand, a power supply to attach to it and program it from the bench instead of in the machine. The customer also provided me with an SD card containing the project file(s) for the machine. I am able to load the project in CX-ONE (running on Win 7) just fine. My computer has a native serial port (COM1) and I built a programming cable to work with the DB9 peripheral port according to a diagram I found online.The processor powers up right away with the ERR/ALM continuously on. No other LEDs came on initially, and after a bit of playing around with communications settings, I finally landed the right protocol and my computer seemed to identify the processor correctly. I compiled the source and attempted a transfer to the PLC. I got some failed message (or maybe messages) at the end of the transfer. It did seem to send all of the binary code, it just ended with an error message that I unfortunately didn't write down or grab a screenshot.Anyway, what I have now is a PLC processor with the ERR/ALM LED on always, I've never seen it in RUN mode, and now after the programming attempt, I'm seeing the COMM LED strobing at about a .5sec frequency (with or without a cable attached to the peripheral port), AND I cannot get CX-Programmer to again acknowledge the processor anymore. I'd like to reset this back to the way it arrived to me, but can't figure out how to make that happen offline. The DIP switches don't seem to cause that effect. I should say also that the DIP switch settings are all OFF except 3 and 7.Any help is much appreciated!Thanks,John  
  2. Hi Y'all, I have been working on a drive upgrade.  I am going from a 1336 impact to a PF 753.  I changed everything over on the Map I/O tree to ethernet.  The question I have is...my Control Net is in demo mode. We are waiting om a tech support contract with software subscriptions to go through.  Will I still be able to download the logix 5000 program that works with the CNET configuration files?  Also I deleted the drive off the config file.  Is there anything I am missing other than drive parameters?
  3. Fatek Ethernet PLC Module online

    Dear All,  Anybody can help me in communication between Fatek 20MAR2 & CBEH2A. The jumpers setting are JP1 is on left two pins (No password protected) & JP3 is on right two pins (forced boot operation mode). The Ethernet cable i used is type b T568. Fatek Ethernet module config software detecting module successfully (shown in attached pic) but on online PLC via ethernet cable its showing connection failed.   please help   thanks in advance
  4. Hi, I am working wih 251MESE and somachine 4.3 And I am developing an application and the user who is going to use it needs to donwload a graphic that appears on the webvis, with all the information that it contains, does anyone done this before? How? I need some tips. I have the webvisu up and running I need something like download button to be able to download the info.   Thanks!
  5. Upload & Download Program

    Hi, I will upload a program from PLC and Download that program to another PLC. Do I need to Compile the program before I download it to the other PLC?   Software: Gx Developer.         PLC: FX-2NC-32MT       Communication Cable SC09 Note: My laptop has only usb port   Thanks for your support
  6. FX-2NC-32MT PLC program Download

    Hi, There are two machine in the factory controlled by Fx 2nc PLC. One machine control part is not working. It could be for battery failure. But the other one is working properly. In this case can I change the battery?  After that,  is it possible, I upload the program from the good machine PLC and download it to the other machine PLC? Regards Sohel Ahmed
  7. I'm trying to transfer an application file to a PanelView 1400e and I'm having some difficulty. We currently have 4 of these in operation on machinery and we acquired a spare that I'm trying to get ready. All use the same exact application. I tried using a memory card but none of the PanelViews recognize any of the cards I do have at the moment so that option is out (though at one time we did transfer the applications this way so we did have at least one card that worked in the past). I was able to extract the application file from one of the PVs via Transfer Utility 32 on Windows XP. I am unable to transfer it back to the spare PV. I am using a 9 for 9 straight through serial cable on COM1 of the laptop to the 9 pin DB connector on the back of the PV. I match settings between the PV and the TU32 (baud rate, parity, error). I put the PV on Transfer Application screen on the Serial tab. I open up TU32 and choose the application file (approximately 86kb in size). If I select memory partition 1 for the destination, I get a dialog that pops up telling me that partition 1 is full and it shows me the size and free space on both partition 1 and partition 2. The size for partition 2 matches what I see on the PV on the Terminal Information screen (approximately 2200kb in size and same is free). When I then select partition 2 for the destination and click OK, it asks if I want to format the destination. If I click NO, the transfer fails because "User did not format the destination". When I click Yes to format, the PV starts formatting partition 2 and the progress bar goes up to 100%, then a message comes up that the format is complete, waiting for application transfer. On the TU32 screen, the format progress goes up to 11% then hangs and eventually reports that the format failed. I've done this a number of times and it is always 11%. However, when I click OK and then go back to the main screen on TU32 and once again select to transfer, the PV screen goes into transfer mode with a progress bar as does the TU32. No progress is ever made and eventually I get the 4209 error. 4209 error means the TU32 and PV are not communicating, basically. But I'm confused as to why they initially do communicate but only get to a specific point each time before communications stop. Any ideas? EDIT: Once I get the 4209 error, I click OK, and go back to the main TU32 screen. If I immediately click to transfer again, the progress bar on the PV disappears and a message comes up saying File Download failed-Ready for Transfer. If I click to Transfer again, the progress bar reappears but still no progress and this process repeats. Thank you in advance for any help you can offer.
  8. Hello, We have a FX3G connected to a FX3U-ENET-ADP inside a main cabinet. We are then using that master PLC to collect data from 2 other fx3g plcs in a node:node serial network. I was assigned a small project of pricing out some wireless adapters so we can upload/download to the two slave plcs. My question is, is it possible to upload/download programs to/from the slave plcs through the ENET adapter and serial network in the main plc? It would save us some money if possible. thanks.
  9. FPWin GR Problem

    Hi, I use Panasonic FP0R 32T PLC. Usually i have no problems to upload or download program to PLC. But, right now the Software, FPWin GR cannot perform the download and upload from PLC task. If i do, the software will be not responding and need to be closed.. Anyone know about this?
  10. Cannot get Online - CPM2C

    Hello Ladies and Gents, Im quite new to working with Omron. I am struggling very much to get online with an Omron CPM2C-S110C. It has a CIF01 card also. I hear this PLC is quite an old one. I have referenced the manual on 'connecting a computer running support software' and double checked I have the correct cables. The ones I am using and the way I am connecting is:-   PLC Peripheral slot >> CS1W-CN118 >> XW2Z-200S-CV >> serial to USB >> Laptop Checking on Device Manager, I have all the drivers installed, the comms ports are correctly numbered yet I still cannot connect. There are 4 dip switches on the top right hand side of the CPU and all are swiched off. I have called Omron Tech Support and they said to ignore them in this instance. The RS232C port on the CIF01 is used by a barcode scanner so there is no means to connect through that (I have been told) I feel that I have been through setting and checked in CX-Programmer and nothing looks obscure. Please offer me any ideas you may have. I would greatly appreciate it. Thank you.
  11. PLC download problem

    Hi, when I download on PLC (R04), sometimes for example. TON timer's output .Q is automatically set to true even though input is false (also on .ET time is 4h ...??). Also, sometimes some bool variables are also set to true even though they are not set by any kind of logic. However, when I physical reset the PLC (power cycle), mentioned problems don't exist. Does it mean that software reset isn't working entirely correct and I need to reset physical PLC (power cycle) every time after I download on PLC? Regards Luka
  12. What is the best way to get to the configure screen when the mer file is set to auto run on the hmi. I need to get this file out before this screen finally quits on me. 
  13. Hello i'm new in all things about plc, i do a project for school and i use a festo fc 34 plc. The plc is programmed via serial port RS232 my pc not support a serial interface and i use a RS232 to usb adapter. when a try to download the program to plc give me a error: "ERROR: Cannot access controller".  What i do wrong.  Thank you in advance and sorry for my English. Have a nice day.
  14. how to program and set up steper use cpm2c-32cdtc-d?
  15. How to download CPM2C-32CDTC-D

    Dear All, i'm download CPM2C to cx programmer, but but download is always failed. Cable condition is good. i was attached my screenshoot about setting my port settings
  16. I have an error message during install GX developer software in my computer "Assign the folder to the network drive or copy from the network to the hard disk when installing the folder from the network (assign the folder shallow hierarchy)" my operating system is win 7 ultimate 32 bit while same program installed successfully with another computer.  
  17. Hi! I'm trying to download program to an e1001 but get errormessage "Unable to connect to Panel". After erasing the applikationprogram in the panel everything works fine. I can connect and download the program. Anyone knows why I couldn't connect or if I could have done differently? Is there some kind of program lock?   BR Asp
  18. I am in the learning phase of HMI and PLC programing and am trying to use some of the hardware that has been donated to me. I have an AB panelview 300 micro terminal and a Micrologix 1000 Plc (they are not tethered yet). I have constructed a small test board with everything mounted to it and have successfully written and downloaded a simple project to the plc with timers, etc.   Now I need to find a way to program the terminal to make changes to the program.   I am looking for some free panelbuilder 32 or anything that will allow me to program the terminal and use it.   Can anyone help me? All help will be greatly appreciated!
  19. I have read that it is possible, in CXDesigner, to download the program from the computer onto a memory card, and then download from the memory card into the HMI terminal. Is a similar thing possible with CXProgrammer, and PLCs? It would be quite useful, for the purposes of updating the program on a customer PLC that is located overseas, when the customer does not own a laptop with CXProgrammer installed.
  20. DC motor with encoder

    Hello, The company that I work for wanted me to design and build a FIFO loader. For those who do not know what a FIFO loader is, it's basically a lift that runs up and down and filling up the magazine slots with pcb's. After I finish the mechanical part i'll try to program it by using a CPM2C - 20. I have already played with CX-programmer and learned my self a bit, for example how to program simple things such as AND and OR gates for controlling motors and lights. Really hard part for me was figuring out how to create a program that reads data from the encoder and use it to create positions which the motor will stop at, and i have not yet figured it out. I've been trying to google it without any luck, the only thing of real info i've got is a 650 page long pdf file or CX-Programmer manual which is hard for me to read since i'm new to all of this. Would be great if any of you people got any source or maybe a manual which are easy to understand for new beginner like myself. A bit about the program i would like to make: The FIFO loader will have some buttons for selecting different programs, lets say you press first button to select "program 1". Then the machine should move up and stop at posision "50" (there are 50 slots on PCB magazine) after it gets signal from pneumatic actuator (which will be used to shove pcb inside the slot) its should move to position "49" and so on.. If FIFO loader is located at "home" position and you press second button to choose "program 2", then it will move to slot "49", wait until it gets loaded, and continue to slot "47" and so on.. The meaning of this is to make a loader which can select a program to fit pcb's with different size of components.
  21. Hi, I'm a newbie, both on this forum and with PLCs, though I do have a software background. I'm helping a friend with a piece of equipment that he's bought. It uses a CMP2C and a NT2S-SF123B-EV2. To save water in his process he needs some timings changed within the PLC. I've managed to do this using CX Programmer. We do have one problem left, the NT2S displays text strings that reflect the old values. From what I've managed to find, the NT2S uses strings stored in the DM area of the PLC. The problem that I have is that I can't find out how to edit these strings. It looks like SYSWIN was the tool for this, but this won't run on my Windows 8.1 machine. Does anyone know how I can do this? Is there anything in the CX One package? Thanks for any help given, Mike
  22. PAROCK1 for HMI/SCADA View File Now a software solution is available for your Modbus (MB) needs in Rockwell/Allen-Bradley Control Logix or Compact Logix (Clgx) family processors, instead of a traditional 3rd party hardware like Prosoft MVI-56, Molex SST-SR4-CLX-RLL etc.  It is an Add-on instruction (AOI) for PLC/PAC firmware v16 or later, (other solutions are available for pre v16 systems).  For hardware interface, use PLC’s channel 0 (serial) or TCP/IP Interface module(s) to have as many MB TCP/IP devices or serial devices.  (Some limits apply based on system configurations, Comm. settings depending on HW used.) Connect any MB Client/Master or Server/Slave device(s) to your CLgx PLC, including flow computers, analyzers, VFDs, Power Monitors, Level gauges, Smart I/O, etc.  All the MB public/native function codes are supported.  32-Bit integers/floats as single entity are supported with byte and word level swapping. A separate utility automates the data mapping to your PLC logic.  Features -Serial Master (BASIC required Option); TCP; Slave; Redundancy; More than 5000 accumulative registers; MB CFC (Custom/Private Function Code) Support; Data mapping too – Between PAROCK1 & your PLC logic; Packaged with Rockwell; TCP/IP Interface Module; Volume Discounts; Annual Support Requirements -Rockwell/AB-CLgx processor with v16 or later.  Contact PCI for earlier versions. -If using CPU’s Chan0, you cannot use Chan0 for any other user mode activity. You can use it for non-user mode activities -TCP/IP Interface Modules from Rockwell/AB supported, are: -1756-EN2xx ControlLogix® Ethernet/IP communication modules, firmware revision 5.007 or later -1756-EWEB ControlLogix Ethernet/IP web server module, firmware revision 4.006 or later -1768-EWEB CompactLogix Ethernet/IP web server module, firmware revision 1.002 or later -1769-L30ER, 1769-L30ERM, 1769-L30ER-NSE, 1769-L33ER, 1769-L33ERM, and 1769-L36ERM CompactLogix controllers, firmware revision 20.011 or later -1769-L24ER-QB1B, 1769-L24ER-QBFC1B, 1769-L27ERM-QBFC1B CompactLogix controllers, firmware revision 20.011 or later -1769-L16ER, 1769-L18ER, 1769-L18ERM CompactLogix controllers, firmware revision 20.011 or later Other Related Services/Items -Custom PLC Add-on instructions building -PLC upgrades, troubleshooting, applications -PC Windows, iOS5, Linux, Mobile devices Comm. Drivers -Custom development, Technology Transfer Services  -Other Non-AB communication drivers for serial or TCP  -Full control system integration, training, architecture design This driver can be conviniently used with Visual Studio in development of complete large scale complex HMI/SCADA Systems. It can be used to perform advanced reporting MES, analytics, IoT, Big data type apps. One example is available to download here For More Info Overview of Parijat Drivers: Click here  Additional supporting Info about Parijat Drivers:Click here Complete Related Driver options: Click here     Submitter Scadadoctor Submitted 03/10/16 Category Other PLC Demo Software
  23. CQM1H-CPU51 Download Program

    hello...... i use of C200HS-CN220-EU Program Download Cable for downloading program to plc. i can work online but when transfer to plc error is check dip switch.... i read manual and dip switch table but cant set dip switch..... please help me to setting dip-switchs for C200HS-CN220-EU Program Download Cable...
  24. Hello! I am working with RSLogix5000 software and writing the program. Very often I need to download the program to the CPU and of course it writes all program at the same time. This downloading makes problem to me, because I loose parametrizised data from the CPU, downloading will always overwrite default values of the tags. Some parameters are written from the panel and I want to keep these parameters allthougt I am downloading new program. How should I handle this? Some tags can be overwriten, some not.