Search the Community

Showing results for tags 'comunication'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 8 results

  1. CJ2M MODBUS

    I have a CJ2M PLC and I have to communicate in modbus with a Lovato reader. I use the MTCP_ETN library but I don't get any feedback as if the communication didn't start.
  2. Hello, I'm trying to connect a CJ1M-ETN21 as slave Modbus TCP with a Modbus/Dali Gateway. I download from Omron website some FB with ones should be possible.   https://www.myomron.com/index.php?action=kb&article=1245 The FB only can be used with the direction unit 0, but we can change some directions inside the FB and can be adjusted to other units. In the download I found this FB: MTCP_ETN_Connect, MTCP_ETN_Fn01, MTCP_ETN_Fn02, MTCP_ETN_Fn03 .... Supposed with connect we can establish the connection with the master, but the FB never make nothing. Should I make some special configurations to use this FB? I appreciate any help. Thanks
  3. Hi, I have an old TSX 47 30 that has an I / O fault (red led on) green led on run and plc stopped. I'm writing to see if you can help me to establish communication and achieve the download of the program. I do not have the communication cable or the PL7-3 software under OS 2. So far I have done searches on the schneider page, forums and all the links are lost or deactivated. I have read your answers in plc of the same series and I observe that a converter rs 232 to current loop is needed. In this case here in Venezuela it is difficult to get this converter, however I have observed the black box model 232 CL-E, CL050A and I think it can be useful. I also have an old toshiba laptop with windows xp with a native rs 232 port to avoid another converter and I could make the connection cable DB25-DB9 to the PLC. Now I would miss the procedure to make an OS / 2 bios and get the software or make a virtual machine in which case I require the appropriate software .. thanks for your help
  4. Mitshibisi to Fanuc Robot with cc link

    Good day all. I was wondering if someone can assist with the setup between a Mitshibisi R08SFCPU using a RJ61BT11 to talk to a Fanuc Robot controller. So in the screen shot attached i added a generic station because i can not find a file for the fanuc robot. The problem is that it does not give me the option of setting the Rx and RY registers. So not sure how to assign the relevant IO. Anyone with knowledge with this would be great
  5. GOT1050 to FX3U-64M

    How configure communication between FX3U-64M and GOT1050? HMI GOT1050 have two chanels availables: RS-232 and RS-422 PLC support RS-422 but i don't know how to configure PLC parameter for establishing comunication with it
  6. cj1w etn21

    first thank u so much i can join on this forum, plc is great for me. now, i have some problem that i never know it before, it's about comunication between pc and cj1w etn21, few days ago my display data on cx supervisor in pc lost and be the#### display. after it i restart my plc n it be normal again but it happen again more often than before until my cj1w etn21 erh led flashing. i try to ping is good conection but sd, rd, tcp led on etn21 modul not lit sudenly and my display lost again. my last efort is i try to set node number on etn21 modul and the erh eror flashing is gone but i can conect my pc again to etn21 modul. so, i set back the last node number and can display again but erh back flashing n data lost sudenly aaain. can you help me please?   
  7. How to configure the connections between the PLC and HMI in the draft TIA Portal WinCC Flexible depending on the type of network we are connecting the touch screen. Read more and have a look to this... http://www.tecnoplc.com/conexiones-wincc-flexible-comunicacion-plc-y-hmi/   -------------------------------------------------------------------------------------- www.tecnoplc.com
  8. RENU FP3035-5 and FL005-0808p

    Hi, Can anyone tell me how to get the FP3035-5 and FL005-0808p to talk to each other via the com1? may be a sample program would be nice. thank Arie