Search the Community

Showing results for tags 'cc link configuration'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 73 results

  1. Hi all, I am working on a safety PLC conversion project, for which I need to identify the input word address configured on a PSS AI IP card. The manual from the official website shows the address configuration via a DOS tool. I do have PSS SW PG WIN 4.9, but the project file has been created with PSS WinPro 2.3. Within this software there is only the option to configure how the input channel behaves, not which input word is used (see attached screen grab). Anyone with a distant memory if the addresses can be set with PSS WinPro?  
  2. Hi, About SmartSlice: „Smart Analog I/O performs data pre-processing to help you reduce PLC programming. Scaling and alarms, and even totalising or rate-of-change calculations are handled inside the unit.” How to get to this honey in case of GRT1-ECT bus coupler and NJ101 EtherCAT communication? What means “Configuration Tool” in W18E-EN-02 “GRT1-series EtherCAT Communication Unit Operation Manual”?
  3. Hello. What is the best option using TCP/UDP communication to use CP1L-EM40 as SLAVE / IO Expansion? For MASTER I’m using CJ2M-CPU31. Since now I’ve used FINS _CPU010_SendData and _CPU011_ReceiveData function blocks. The problem is, that I’m communicating with 6 slave IO units and to read/write all 6 units it takes up to 1 – 2 seconds. I’ve tried Ethernet/IP protocol but CP1L units doesn’t support this protocol. Is there some kind of different TCP/UDP protocol which is faster than FINS?  In older days you could use PC Link but this protocol is for RS232 / RS485 comm. I know I could use CP1W-EIP61 but I don't have this adapter and I can't afford to buy one Thanks. 
  4. Hi everyone, I have a question for you all, Is possible to configure CJ2M-CPU11 with tags trough network configurator to connect Control Logix PLC using EthernetIP? I did a configuration with CJ2M-CPU31 and Control Logix PLC with no problem, but now I need to communicate CJ2M-CPU11 with Control Logix PLC using EthernetIP. Some of you did this configuration between this two PLC before? Regards!
  5. I am trying to setup a CC Link between two machines. I have done this before without issue, but for some reason this is not going well.. I added a second CC link card to CPU2 and set it as ST 24 for the CPU1 network.  CPU 1 : Master.   cc0.jpg.   The original machine was setup using TO/From for each station, so i couldn't add this new link through the GUI.  CPU 2: Local cc1.jpg  When i try to use the GUI to setup this side the buffer stops working. but if i activate any TO/From instruction here i get a system fault with a 2110 SP. Unit Error CPU2 buffer cc2.jpg. But when i block the TO/From you can see the buffer is working at that exact same location specified.    2110 error says I am addressing the wrong card but the buffer proves that I am not. 
  6. CC-Link IE Protocols

    Hello, There seem to be a lot of different CC-Link IE protocols: CC-Link IE Field Basic CC-Link IE Field CC-Link IE Field Motion CC-Link IE Field Safety CC-Link IE Control CC-Link IE TSN This causes me some confusion. Are there as many variations of Ethernet/IP and PROFINET? Can you point me to a good comparison of the different CC-Link IE protocols? My understanding is that: CC-Link IE Field Basic: 100 Mb/s Non-deterministic? Good for non-time-critical communications (e.g., setting a drive speed) Implemented in software Traffic can co-exist with other TCP/IP traffic Max 64 stations Addressed by IP address Star topology I believe the other protocols are all 1 Gb/s, are deterministic, are addressed by station number, are implemented in hardware and each needs its own isolated network. CC-Link IE Control is used for communications between PLCs and robots. CC-Link IE Field is used for remote I/O and CC-Link IE TSN is used for even faster remote I/O communications. Please let me know if any of this is inaccurate. Thanks,
  7. RJ71EIP91 Configuration mismatch

    I have several machines that use the RJ71EIP91 module. I have not had any issues until now. I do not have the original apa file. I upload the configuration and try to restore it from the configuration.apa file, it does not show everything that is connected to the card or programmed in the PLC. when I verify this it says that the configuration is a mismatch. I have several of these scattered throughout the factory and I don't have this problem anywhere else. Is there a solution to this problem?
  8. Hi All, I just start to setup a rotary servo (rotary transmission load type) and the designer pass me the spec of gear ratio 1:100. In my motion scaling page, I set Transmission I:O as 1:100  and then scaling unit is just position unit with 1:1. However, when i jog my rotary servo, it does not reflect the actual position in degree, so I went to read through the manual but still cant quite get how should i configure my scaling so that I can see that when the motor is rotating, i can see it rotate how many degrees? I try to set scaling 360 degree to 1.0 load rev, and the position feedback seems like much more finer....
  9. Hello, I currently have a PLC in a machine that is a CP1H. A newly developed machine uses a CP2E PLC. The newly developed machine is supposed to communicate with the CP1H where the CP2E is a slave. I am not able to find much documentation on this specific set-up. I was wondering how to set this up. As the shared words of each PLC are on different adresses. I can't really find any documentation or any examples on how to do this. Can somebody help me with where to start with this?   kind regards, Ralf
  10. Hello friends I have worked with other series of omron plc but this is the first time I am working with cqm1h cpu51 series. In a factory, 4 of these PLCs exchange data with each other with a clk21 card. After a problem with one of the CPUs and replacement, I was never able to download the datalink settings. I did all the steps in the manuals step by step but I did not succeed. In cx-net software, after selecting online, I selected the data link menu, but as you can see in the attached image, the setup button is never activated. Thanks for guiding me
  11. NE1A-SCUP02-EIP

    Does anyone have experience with the NE1A-SCUP02-EIP safety PLC? We had a machine shutdown yesterday with a L9n4 error on the NE1A unit. The manual says this is a tag data link error. Does this cause the safety PLC itself to shutdown? I always thought the EIP portion of the safety PLC was only used for status reporting to the PLC. The safety portion is strictly on DeviceNet and is independent of the EIP network.  The CJ2 PLC's error log tells me it had problems communicating with the safety PLC, the VFD, and NX I/O's which were all in the same panel going through an Ethernet switch. 
  12. can i cc link  Fx3U-64CCL  with FX2-32CCL without any problem
  13. Is there a way to run a compact logix program, while ignoring the the I/O configuration?   I used to do this with other PLC's to help develop the HMI screens while connected to development PLC that does not have the full complement of cards that the end user PLC will have.  Just lets me test logic that supports the HMI while working at home.   I used to do this on other PLC's with just a CPU on my desk.   Possible?
  14. Input cards, DI8x24VDC BA, 6ES7 131-6BF01-0AA0, NEW in box ,quantity 10 IO-Link CD-Master 4SI SIRIUS, 3RK1 005-0LB00-0AA0, NEW in box, quantity 4 IO-Link Master 4SI IO-Link, 6ES7 138-4GA50-0AB0, NEW in box, quantity 3 IO-Link Communication Module, CM 4xIO-Link, 6ES7 137-6BD00-0AB0, NEW in box, quantity 1 CM AS-Master ST, 3RK7 137-6SA00-0BC1, New in box, quantity 1   Located in USA.  Make offer, shipping included.   Pictures available on request, send email address in a PM.
  15. I am new to PLC programing, I want to connect FX5U and MR-JE-_C via CC-link. When I connect FX5U and MR-JE-_C directly everything works, but when I connect them in HUB (I need to use HUB because later I want to connect GOT2000) I am getting error 86.1(network communication error) on amplifier. Previously I set up IPs shown on pictures below, now sometimes works, sometime doesn't work and sometimes works for 30 seconds and I get same error. Did I miss something? I don't know what to try else.  
  16. Simatic pc to simple pc with profibus card

    Hi every one, One of my machine i have to fix , has simatic pc unit installed that causing too much trouble  and client want to replace it with simple pc with additional profibus card installed in PCI slot, is there any way to configure image of simatic pc in new simple pc
  17. Omron NJ501 - IFM IO-Link - Wenglor U1KT001

    Hi, I am looking at reading an ultrasonic sensor value through IO-Link, using a Omron NJ501-1320 PLC connected through EtherCat to a IFM AL1332 master with a Wenglor U1KT001 Ultrasonic sensor. I have managed to read the 2 outputs of the sensor using this: Output_1 := TestABit(USINT_TO_BYTE(TxPDO_input_byte_1_6000_02),USINT#0); Output_2 := TestABit(USINT_TO_BYTE(TxPDO_input_byte_1_6000_02),USINT#1); But cannot read the ultrasonic sensor distance value, this is what page 2 in the manual says: Measured Value in 1/10 mm 2…15 14 Bit 300…4500 Octet 1 Subindex 3 (LSB) 2 1 Bit Offset 7 6 5 4 3 2 1 0 I tried a couple of conversions but couldn`t get the distance reading. Any ideas? Help appreciated.
  18. Hello everyone! I've installed GX works 3 according to the instructions in "https://plc4me.com/gx-works3-v1-308q-mitsubishi-full-real-100/". I don't get any errors, I can run the PLC and simulate completely OK. In the communication test, when the configuration is missing some components in the module list: Input, output, I / O module,... (https://ibb.co/ZVMcmQn) I hope you can answer for me?
  19. Hi, I've got a very old version of Wonderware, version 9.5, which isn't going to be upgraded anytime soon. I would like to configure a button to perform 2 tasks under "Touch Pushbuttons", ideally "Action" and "Show Window". I am unable to enable both at the same time, so I've been trying to write a script that would perform both functions, but so far unsuccessfully. Is this something that can be done, or is there another way to get around this problem? I would like the button to toggle a bit and to open another window with more controls.   thanks
  20. Hello everyone, As the title suggests I am trying to display on a GOT1000 the real time frequency that the inverter is running at. I have attached my CC-Link settings and the associated programming as well. I tried using the example program from Mitsubishi but I got lost. From my understanding I should be seeing the output frequency in W3C4 however, I am not receiving any data. Any help would be appreciated. 
  21. HMI on CC LINK IE FIELD

    Hello all, kinda lazy question, but I'll rather ask, before I'll went to deep into HMI scripting. Because of a design of CC link, there are RWr and RWw Is there any simpler solution for displaying value stored in PLC, while also letting HMI operator change the value and save it to PLC, than scriting in HMI? hope it makes sense to you thank you in advance
  22. The CC-Link system on a machine has been intermittently dropping out.  Normally the Link Scan Time runs at a solid 87ms.  When the system "drops out", the link scan time will increase.  Sometimes double, triple, or go up 10x. It happens when the machine is running or when it sits idle. There are 33 stations on the network.  The same stations do not always fault but sometimes all of the stations will fault at once (as seen in the attachment pictures.) We have changed the main QJ61BT11N, the processor, the Q62N power supply, the main backplane (base unit), all cards on the main backplane.  Is it possible for one station or one of the cables to create a network wide problem?  Any ideas thrown at us would be appreciated. 
  23. CC-Link Protocol with a CJ2

    I have an IAI servo that was sent to us with CC-link protocol. I have never in my life used cc-link and can find very little on the topic on integrating with an Omron CJ CPU. I am curious as to whether this has been done, or is even possible given the protocols Omron works with. And if so, what did you have to do to get the PLC to communicate via CC-link. Thanks in advance for the responses!
  24. Mitshibisi to Fanuc Robot with cc link

    Good day all. I was wondering if someone can assist with the setup between a Mitshibisi R08SFCPU using a RJ61BT11 to talk to a Fanuc Robot controller. So in the screen shot attached i added a generic station because i can not find a file for the fanuc robot. The problem is that it does not give me the option of setting the Rx and RY registers. So not sure how to assign the relevant IO. Anyone with knowledge with this would be great
  25. RIWT special relay

    Once agin hello all, im pretty sure, that in the past i found in some manual special relay (SB????), that was set on when PLC was executing RIWT instruction. Now im trying to find once again, but with no luck, ive searched through all manuals that looked relevant, but nothing... any help will be highly appreciated.