Search the Community

Showing results for tags '5069 compact logix red lion communication'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 259 results

  1. Hi All, Hope you all doing well in this pandemic life.  I would need your expertise with an issue I have been struggling with for past few days and thought to reach out here. I am working on a migration project with GE PLC and Citect SCADA 7.10. The GE PLC is migrated to ControlLogix L74 Rev24.10 while Citect SCADA is retained. For testing I only have L71 and L82 and could not managed to organise L74. When the code the loaded in L71 and connected to Citect, I cannot see tags in Graphic page but I see the subscription.txt in Debug folder shows all tags good . The same code when loaded in L82, the Citect works instantly.  Does anyone know this behaviour of PLC and SCADA? Regards, DeeEngr    
  2. Hello All, First time working with PLC. Get the hang of it from stuff I researched. Having an issue with an axis setup for a servo motor.  When I try to do an auto tune it gives me an error that axis is not configured.  Source: Config Fault    Condition: MotorDeviceCode- INvalid attribute      ACtion: Immediate Stop Fault Entry: Type 8, code 9 subcode: 1314 stopaction: 4 Statechange: 3   I was wondering what am I doing wrong? Any leads or source information I can use to solve this. 
  3. Hi, got a mental block lol.  Got a machine we are modifying, currently got most of the code in place. Working on a fault routine now. This machine doesn't have an HMI or wide array of PL. Nothing major just a simple vision system check. Currently have 6 faults that will stop the cycle running. I'm wanting to have the beacon light (Red light) blink for the cause of the fault. For example: Scenario 1- Fault stop for bottle check NG:  (two) .5 sec blinks -  2 sec red light off -  (two) .5 sec blinks ..... repeat  Scenario 2- Fault stop for bottle check NG and reject sensor blocked:  (two) .5 sec blinks -2 sec red light off - (three) .5 sec blinks - 2 sec red light off....... repeat I have the code a few different ways but it looks "dirty". Any suggestions? Thanks in advance  
  4. INFO

    Dear sir, I am working in container terminal, we have Siemens plc  s7-300 , Bromma spreader with SCS-3( codesys software) spreader field device sensor (ifm) connected to slave ifm CR9011, now a days we are facing too much issues in scs-3 so we planned for isolate the SCS-3 but we want to know ifm module Cr9011 how to communicate to Siemens plc  7 how to write in hardware configuration. can you please suggest us.  
  5. How can I determine if both my Produced and Consumed tags are communicating with each other, and if have the right set of tags since I forgot how I named them?  Is there a way to confirm that both my P & C are communicating.
  6. I have IPC and need to detect status of IPC and PLC communication . I need help with the same that how can in detect it ? Is it possible with message instruction ? if it is then how ?
  7. Can anyone help me with the issue in the picture? We have the correct version in place yet it gives me a version error stating it needs the version that is installed. Doc1.docx
  8. CP1L-EL TCP/IP with VideoJet Printer

    Hello, My previous topic was want to establish communication CP1E --> Videojeet Printer using RS232 serial cable. this project test SUCCESS. by the way distance from printer and PLC was very far almost 500meter. so printer technical team request to use tcp communication using cat5e cable. Problem: 1. I'm using TCP communication protocol that need me to have open,send,receive,close port. 2. Communication testing with PC Hyper Terminal --> OK but HT need in waiting call mode, i don't know why. 3. Using printer no result show. how i'm suppose to know communication already establish? 4. Communication setting on PLC Setting-Built in Enthernet need to add other communication device.? here i'm share some programs to give more understanding. Thanksm TCP with printer.cxp
  9. Hello. I am trying to make a serial RS 232C connection between Schneider Magelis HMIGXU3512 and Omron PLC CP1E. However, there seems to be a communication problems between both of the equipment. I am using cable XBT Z9740 for the serial communication cable. The format used is 8.2.N for both equipment. The baud rate is 115200. No Flow Rate is choose. Anyone can help with this kind of problems?
  10. Hi All, Am trying to communicate and make In-Sight bar code reader to trigger through MicroLogix 1100 with RSLogix 500.  Does any have any info as to the steps to follow. Most of the info I saw and have tried were for SLC processor In fact, I created the String file ST10:0  for the target device as was mentioned in one of the posts but when I complied it there was error saying that St10:0 was not supported by the module. Please see attached file. Any insight will be appreciated  
  11. LOCAL MELSEC COMMAND

    Hi everybody,  Is it possible to send MELSEC commands to oneself, locally, not using the phiysical ports? I would like to use some commands described in the "Communication_Protocol_Reference_Manual_(MELSEC)" to get some self-management functions in my PLC.  For example, in OMRON this is possible using CMND instruction and setting the FINS address to 0.0.0 in the parameters of the instruction. Thank you very much. 
  12. Diagnostic of profinet communication

    Dear Experts, I want a sample block to find out the status of my Profinet cable w.r.t Hardware configuration. whether the cable is connected or disconnected from the node. Either my nodes may be VFD, HMI, SCALANCE, etc...  please share the sample blocks... S/W ===== >Tia portal v14 sp1 update 6  H/W ===== >CPU 1214C DC/DC/RLY hanks in advance
  13. Hi Im hoping someone can help me out! i have a PLC SLC 5/03 and i want to connect the DB9 port with DH485 protocol to a computer 100 fts from there, is there any problem with the distance? and what kind of cable should i use , i already connected with my laptop with a USB-serial with a null modem cable RS232  (i did the cable by my self) but for the distance i cannot keep using that protocol so what is the recommendation?    
  14. Mitsubishi plc communication error

    I have Mitsubishi FX-1N P.l.c i found a problem about communication port.Run and Power L.E.D on as per routeen but i cant communication with GX.Works 2. PLz tel me how can i fixit this problm....
  15. Hello  We have just purchased some equipment with a Control Logix 5561 (1756-L61/B Rev 13.40). The compact flash card is missing from the unit but the seller says the unit was running in his facility prior to shipping. Does the 5561 have internal memory where a program is stored? Is the Compact Flash used only for recipes and persistent data? Thank you
  16. IC220PNS001

    Hello, I currently have two IC220PNS001 connected to IC695PNC001. The PLC being used is IC695CPE330. Out of the two PNS001, one of them has a solid SF Red light on which means bus error according to the Status Parameter IO. I disconnect every single IC220 card connected and downloaded the whole configuration but I still have a Bus error.  PS: I have also tried to switch the PNS001 with the brand new out of the box and I still have the same error. In the manual, it says Profinet Diagnostic available, can somebody please guide me as to where I can find the Profinet Diagnostic, also is there any manual for PNS001 which explains the in-depth debugging process for this PROFINET Controller.  
  17. I'm wanting to get upload the program from a CompactLogix L31 Controller.  I'm using a generic (non Allen Bradley) "C2G brand" usb -->rs232 cable coming directly off of my laptop because I don't have a serial port out.  The rs232 side of the C2G cable is a "pin out" or male end, and as you can see in the picture, the serial port at Channel 1 on the controller is also male.  I'm using a generic (non-Allen Bradley) null modem (female-->female) cable to complete the connection.  Ultimately, I'm not seeing the controller on linx.  But that's a result of me not being able to configure the driver.  When I try to auto configure this driver, Linx gives me an error saying, "Unable to verify settings due to a NAK!" btw, the rs232 cable going into channel 0 is for the HMI on the machine. A pv600 1. How do I get online and upload the program from the controller? 2. What does NAK mean?
  18. Diagnostic of profinet communication

    Dear Experts, I want a sample block to find out the status of my Profinet cable w.r.t Hardware configuration. whether the cable is connected or disconnected from the node. Either my nodes may be VFD, HMI, SCALANCE, etc...  please share the sample blocks... S/W ===== >Tia portal v14 sp1 update 6  H/W ===== >CPU 1214C DC/DC/RLY hanks in advance
  19. I am trying to get produced and consumed tags set up between 2 1756 racks with different ip's. The 1st rack has an ip address 172.28.6.3. The 2nd rack has an ip address of 10.81.105.8. Would this be as simple as adding an EN2T card to one of the racks and setting the ip of one onto the same network? Or is there a better way to do this?
  20. Series 90-30 CPU311T With Proficy ME

    We have an old press using a Series 90-30 with a 311 CPU 5 Slot Rack.  I am trying to pull the program off so we can convert it to a new CompactLogix.  I am using Proficy ME v6.0.  I have the proper RS232-485 cable and a built in serial port on my XP laptop but cannot get it to connect.  I know that Logicmaster projects cannot be opened by Proficy ME and being such an old 90-30 it probably was programmed using Logicmaster.  Would being programmed by Logicmaster prevent me from even being able to communicate via serial connection?
  21. Gentlemen, I'm new to Siemens and now working on a project for my client. I have a S7 1241 cpu,  CM1243-5 com module, a KTP700 hmi prifibus dp. The hmi is connected to the CM1243-5 via profibus cable. My problem: I'm not able to detect the hmi. My plc is connected to my router and I'm able to get online with it.  I've attached some diagrams..just in case. Appreciate any help. thanks, Moorthy.   
  22. Hi all, i just need to clarify that can we use GTSoftGOT2000 to work with QnACPU. i am describing my situation below. We have a vendor asking asking us to install a Large Screen where a operator can see the images of the faulty parts with respective of what part they run(we run almost 14 parts on one machine). the largest HMI that i was able to find was a 19inch one from Pro-Face, but thats not sufficient . so got and idea of using GTSoftGOT2000 and create a HMI screen and connect it to a PC Moniter. 
  23. Hi all, i just need to clarify that can we use GTSoftGOT2000 to work with QnACPU. i am describing my situation below. We have a vendor asking asking us to install a Large Screen where a operator can see the images of the faulty parts with respective of what part they run(we run almost 14 parts on one machine). the largest HMI that i was able to find was a 19inch one from Pro-Face, but thats not sufficient . so got and idea of using GTSoftGOT2000 and create a HMI screen and connect it to a PC Monitor. and do a slide show of pictures of faulty parts of a specific model of what they run. 
  24. CP1E-N30DT with Hyperterminal PC

    Dear Expert, i'm issue to do communication CP1E with PC via RS232. im try to use plc for sending information and receive by hyperterminal pc. after googling some information there have multiway to success. by the way until now cannot settle. please expert share completed setup that's work: 1. communication cable from PLC - PC (my information use pin (2,3,9 jumper 4&5) - (2,3,5 jumper 7&8) 2. sample program that works (im using TXD & RXD with memory D1000 to keep data) 3. connection cable to PC using MOXA Serial to USB converter. 4. plc serial setting (default: 9600,7,N,1,Host link) my target to give instruction to printer to start print. printer need ACSII code. if this communication success i'm will convert all data to ACSII by ACSII convert function.   thanks,
  25. I'm upgrading from a Panelview 550 to a Panelview Plus 600, I already have the HMI files converted. The PLC is a SLC 5/03. I found this post, I am wonder if there is other options besides using a 2711P-RN3. A quick Google seems like it's obsolete, but I am waiting to hear back from a sales guy. http://www.plctalk.net/qanda/showthread.php?t=105902 I am wondering if I should be able to use the rs-232 serial port DF1 full duplex.