Search the Community

Showing results for tags '3phase current monitoring'.

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Found 16 results

  1. Are there any current recipe examples for omron na hmı?Are there any current recipe examples for omron na hmı?Are there any current recipe examples for omron na hmı?
  2. I have a level measurement system by fmcw radar (Rosemount tankradar), for a filling-emptying process, of very large water chambers. Very sporadically, the radar is momentarily lost and measures 4 to 7 feet below the actual level, only when filling the water chamber.  Sometimes the measurement freeze in the middle of the filling process.  Due to the criticality of the process, this behavior is dangerous, as it can cause flooding inside the plant This behavior is very sporadically so we are baffled about the root cause of this problem.
  3. I have project where I need to measure motor current but I do not need to control the speed of the motor since it would always be running at full speed. Do I still need to use VFD to get feedback or is there cheaper way to measure the current?
  4. Hello, I'm looking for a simple data logging software, something that doesn't require any programming skills. Thank you!
  5.    Have 10 POE Analog Input Modules available on clearance  10/20-channel Voltage Input, Current Input, & Analog Input Module with High Voltage Protection PoE Module, communicable over Modbus TCP and Modbus UDP    Model Number PET-7017-10     Regular price $459.00/EA    Clearance price $344.25/EA   only good on clearance quantity only.   http://www.icpdas-usa.com/pet_7017_10.html      
  6. CJ2m and NB10

    hello guys, My situation is, I have an HMI nb10 and PLC CJ2M-cpu31. My question is, how can I monitor my system with this two set up of Omron device thru online or web base . They are connected via ETN cable. What should I do and what are the ways to monitored it. please help me guys. Thank you.
  7. Hi to everyone, I use PowerFlex 520 drive on profibus (with adapter 25-COMM-P) for first time. I managed to start/stop/reference drive using Logic Command/Status I/O but didn't manage to get output current using datalinks mechanism. I configured DP master (Mitsubishi Q PLC, QJ71PB92V) as shown in the attached picture. The main problem is that trying to modify C161-C164 (Opt Data In 1-4) parameters drive does not accept the entered values and it turns back to value "0". First, I disabled I/O connection with the controller Disconnecting the drive from the network. On the other hand, drives allow me to change parameters C165-C168 (Opt Data Out 1-4) but these are out paramenetrs (from the controller's point of view). Is there any guy that managed to get the output current  in any way on profibus network? Thanks a lot for your help in advance! I post this message in Allen Bradley Forum, too.
  8. Hi to everyone, I use PowerFlex 520 drive on profibus (with adapter 25-COMM-P) for first time. I managed to start/stop/reference drive using Logic Command/Status I/O but didn't manage to get output current using datalinks mechanism. I configured DP master (Mitsubishi Q PLC, QJ71PB92V) as shown in the attached picture. The main problem is that trying to modify C161-C164 (Opt Data In 1-4) parameters drive does not accept the entered values and it turns back to value "0". First, I disabled I/O connection with the controller Disconnecting the drive from the network. On the other hand, drives allow me to change parameters C165-C168 (Opt Data Out 1-4) but these are out paramenetrs (from the controller's point of view). Is there any guy that managed to get the output current  in any way on profibus network? Thanks a lot for your help in advance!  
  9. I'm doing some remote support on an FX5U with GX Works3 on the remote desktop. I've been doing this for a couple of weeks without difficulty. Yesterday the ladder monitoring stopped working. There is no ladder contact monitoring showing and D registers and timer values are blank. The Watch windows are working correctly. Online Write Monitor is selected in each case. All Tools | Options seem correct and match my local copy of GX Works3 that I used on site. Any ideas?  
  10. FX3G-2AD-BD Store Peak Value

    Good day, I'm new to this forum and to mitsubishi PLC but was hoping for some assistance with a programming issue. I have been through the hardware and programming manuals without luck for this issue. Hardware: FX3G-60mt FX3G-2AD-BE Settings: Structured ladder/FBD Current input mode on: M8260 (first board, first input)   What I need to do is to record the peak value over a cylinder stroke period. The hardware manual explains how to average the value using averaging time, however I basically need to peak hold and send that to a D register for go no-go compare.    Process as follows: Contact closed, monitor D8260, contact open, move peak value from D8260 during monitor duration to D205.    Thanks in advance for any assistance. -Swervomotor  
  11. Version 1.0.0

    84 downloads

    Temperature measurement usind Arduino Nano, RTD PT100 sensor,  4-20 mA current loop transmiter, and a python app for visualization
  12. View File Temperature measurement using Arduino Nano, RTD PT100 temperature sensor and 4-20 mA transmitter Temperature measurement usind Arduino Nano, RTD PT100 sensor,  4-20 mA current loop transmiter, and a python app for visualization Submitter Absolutelyautomation Submitted 04/01/16 Category Other PLC Demo Software
  13. Current Monitoring

    Greetings, I've been having some issues with a vacuum pump breaker tripping... I think I've figured out the problem and resolved it but I noticed that several of the other motors have current monitoring on the HMI but the person who set this up is no longer with us.  I'm wondering what I need besides an analog input for my control logix processor (which I have) to setup this project.  I'm not sure if the other motors are just monitoring one leg of the 3 phases or if they are somehow showing total current?  any ideas and recommendations would be greatly appreciated.   thanks,
  14. Micrologix 1400 Problems

    I have been using a micrologix 1400 L32bxba. I have had a reoccurring problem of the contacts sticking on the processor. I have added diodes on the coils of the contactors. Using 700CB220EJ relays. I also have the problem of the leakage current being so high it pulls in the relays with the output off. Any help would be appreciated.
  15. Hello everybody, I am connecting my DCS digital output (115VAC) to AB PowerFlex 753 Digital Input. We are using the 20-750-2262D-2R I/O option in the powerflex which is 115VAC I/O with 2 Analog In, 2 Analog Out, 6 Digital In and 2 Relay Outputs. My question is, what is the current or power consumption of the PowerFlex DIs at 115VAC. I need to specify the right fuse size for my digital output. Thanks,
  16. Hello, anyone know how to make a logic that monitors the change in position of a carriage through some rails ?. In my application I measure the position of the carriage by means of a laser sensor and I have to detect if the laser beam is interrupted when the carriage is stationary or moving. I have implemented a logic as the adjunct file, but doesn't work.