gowthamsudherson

MrPLC Member
  • Content count

    9
  • Joined

  • Last visited

Community Reputation

0 Neutral

About gowthamsudherson

  • Rank
    Newbie

Profile Information

  • Country India
  1. Diagnostic of profinet communication

    Dear Experts, I want a sample block to find out the status of my Profinet cable w.r.t Hardware configuration. whether the cable is connected or disconnected from the node. Either my nodes may be VFD, HMI, SCALANCE, etc...  please share the sample blocks... S/W ===== >Tia portal v14 sp1 update 6  H/W ===== >CPU 1214C DC/DC/RLY hanks in advance
  2. Diagnostic of profinet communication

    Dear Experts, I want a sample block to find out the status of my Profinet cable w.r.t Hardware configuration. whether the cable is connected or disconnected from the node. Either my nodes may be VFD, HMI, SCALANCE, etc...  please share the sample blocks... S/W ===== >Tia portal v14 sp1 update 6  H/W ===== >CPU 1214C DC/DC/RLY hanks in advance
  3. Alarm logging

    Dear Experts, For alarm logging and trends i need clarification of Limitations of range as following 1.How many alarms can be logged in Alarm buffer (please dont explain only in terms of memory)  2.If alarm buffer size is vary for each HMI means where shall i found whether it is in any documents or it is in hardware set up? 3.How many trends can be log without memory card and with memory card (please dont explain only in terms of memory) if the following is true then it will suitable for all HMI's ? There is the buffer size maximum 999 Values. The time span depends on the setting you set at "Source setting" -> "cyclic" of the trend. for example if you use 1s then every second there will be saved a Value in the buffer and if you use 999 Values the time amount will be only 999s. But if you use 10s as setting for example the Buffer´s time amount is 9990s. Thanks in advance.
  4. Sample blocks for S7 1200 plc's

    hi  i want motor blocks , valve blocks and analog blocks standard for s7 1200 PLC and it shoud be open in tia v14. please note that this blocks should be developed by ladder or STL only. 
  5. Sample blocks for S7 1200 plc's

    No it should not open only Tia v13.1 will open the all previous version of Tia portal . And Tia v14 opens the Tia v13.1   So thats the problem ............and its okay thanks for your support......... i started to develop my own block in tia v14...........
  6. Sample blocks for S7 1200 plc's

    hi  i am having software already but my laptop is not compatible. So please share the backup for editable timer 
  7. Sample blocks for S7 1200 plc's

    Hi experts, please share the sample blocks for the EDITABLE TIMER block it should be editable from HMI(Siemens). And also motor run hour block. Actually i am having all blocks in tia v12 version and sadly i dont have the old software to convert it again. So please share the blocks that it shoud be work in TIA V14 for s7 1200 plc's. Please note that the blocks should use add instructions to calculate the time because i don't have much memory.
  8. CP1E PLC AI scaling logic requires

    Thank you very much Mr.Michigan and  Mr.Guru yesterday itself i downloaded the sample backup from our forum itself , but it took 2 hour to get it. Example.cxp which i attached here and please confirm whether it works or not ? and thanks once again
  9. CP1E PLC AI scaling logic requires

    Hi experts, Am using the CPU type CP1E PLC and AI module CP1WADO41, my doubt is that as per the attached manual For 'D0' we will get the raw value as counts from AI module. With help of this value how shall we scale the range ?  for example: My minimum value is 0 kg maximum is 1000kg with above example we will get the raw counts from PLC and how shall i convert into a scale (as my application)?