iic_hyd

MrPLC Member
  • Content count

    43
  • Joined

  • Last visited

Community Reputation

0 Neutral

About iic_hyd

  • Rank
    Sparky

Contact Methods

  • ICQ 0
  1. RS-VIEW & RSL500

    Dear Bob, Thanks for your reply, i want to convert 4-20mA analog signal into Flow and Totaliser Thanks and Regards Ns
  2. Hi, Can any one help in how to rotate an object in RS view? Flow indication and totalizer simple calculations in 500? Thanks and Regards NS
  3. Hi, First you check for RS Links, if it is RS Links Lite it will not work. NS
  4. Analog Input Problem

    Hi, it is very user friendly to use siemens products any how follow the steps given below will solve your problem Considered your input to 1st channel is 0-10VDC then 1.Check the jumper setting and makesure it is in correct possition 2.connect 9V battery to correct terminals on 1st channel (common and Voltage) 3.Go to hardware check for channel setting for 0-10 Volts 4.Check for 1st channel address 5.Check module status online if ok 6.type the address in monitor modify variables and check for digital value around 30000 approx. if it is ok then connect your external device no if you have any problem it is sure there is a impudence mismatching problem in between then use a 0-10 VDC to 0-10VDC singal isolator it will solve your problem Regards N.Subrahmanyam
  5. Modbus

    Hi, Thanks for your reply any how i will explain briefly as below I have SLC-5/05 connected to switch, and further to SCADA station RSview, i have a third party devise that is Carrier make Chiller with Modbus it needs to be controlled from SCADA station i.e. reading process values and writing set values and on/off of chiller, for that i am planning to connect the chiller by using a Modbus to Ethernet converter so that i can connect chiller to switch via this converter but now how can i do the programming in RSL500 please suggest if you have any idea. I know it can be done by using a ML1100 or Prosoft please tell me if any other method is there Thx N.Subrahmanyam
  6. Modbus

    Hi, Can any one tell us, how to read and write the addresses via Ethernet from SLC 5/05, where i connected Carrier make chiller to etherent network (By using a Modbus to Ethernet converter) i used AB SLC 5/05 which is connected to the same network. Thx N.Subrahmanyam
  7. MPI PC ADAPTER

    Hi, You can use your MPI Adaptor for S7-300 and 400 Also but you need PPI Adaptor(6ES7-901-3CB30-0XA0) for all S7-200 CPUs. Ns.
  8. S7 300 & 400 Back Up Batteries

    Hi, For S7-400 There will be 2 Batteries you can switch to second one and then change the first one. Rg Ns
  9. 1 I/P 2 O/p

    Hi, Thanks for your reply any how you can consider S7-200/SLC500. Infact there will be a cam which rotates and activates Limit Switch and th Limit Switch will be on for more than one sec.which is sufficient to drive solenoid, main problem is with very old hydraulic system in this we need to control turret index, for this there are two Solenoids , when we power up we can on any Solenoid to index but next time we need to on the other one again first one, this is the sequence. Regards Ns.
  10. 1 I/P 2 O/p

    Hi, I want to control two out puts by using one input, i.e. when input is high 1st out put should become high, again second one and this cycle should continue, please suggest how to control with out using timers or counters. Rg. Ns.
  11. HI, IT IS POSSIBLE YOU JUST SELECT DDE SERVER IN RS VIEW AND CREATE A TOPIC IN LINKS ORKS FINE. RG NS
  12. HI, I AM TRYING TO COMMUNICATE BETWEEN SLC-5/05 AND CARRIER CHILLER, FLEXLOGIX L34 AND MCQUEY CHILLER.I HAVE CONNECTED BOTH THE PLCS COMPORT THROUGH RS485-232 CONVERTER INBETWEEN, PLEASE TELL IF SOME ONE DID IT HOW TO READ AND WRITE THE HOLDING REGISTERS ETC IN RSL-500 AND 5000. REGARDS NS
  13. Step7 V5.4 authorization key lost

    Hi, Contat your local Siemens office with all of your License Details they will help you to retrive it, meanwhile you can use Emergency disk for 15days if you get with your package.
  14. 1788-ENBT

    hi, greetings, Thanks for your reply any how i will try to use IP Scanner
  15. Hi, Can any one tell what will be the cabel like Straight or Crossover between a PC and 1788-ENBT ethernet Module of a Flex system. regards N.Subrahmanyam