Maher Salem
MrPLC Member-
Content count
42 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Calendar
Everything posted by Maher Salem
-
cant connect HMI omron to PLC omron [solved]
Maher Salem replied to riandanualdy's topic in HMI & SCADA
how did you solve it ? -
Dear Experts i have HMI weintek MT8121x when it is powered on it shows that messages in the photo is the project file damaged ?? how can i solve this
-
ok, how much it cost ??
-
Hi All Experts, i'm new in Beckhoff i want to buy an embeded PC cx5020-0115 that is coming with TwinCat3-XAR will i need a lincense ?? or its fully activated ?? thanks in advance
-
thanks for your information how can i buy the suitable license ?
-
Dear All are there any vailable updates version of the motion module R88A-MCW151-DRT-E ?? i searched for it as New and in-stock but i didn't find please help
-
Dear all experts i want a cable pinout to connect the plc FX1N-60MT-001 to MT6103ip HMI can you help me with a tested pinout ?? if i want to connect the same HMI with FX1N-232-BD kit what are the differences which i should take in considerations ??
-
Hi all Experts, what is the difference between the 2 SSI modules CJ1W-CTS21 and CJ1W-CTS21-E if i want to use the CJ1W-CTS21-E , how can i add it in IO table ? its not found
-
Hi All, i want to add an encoder module to the IO table with CJ1M-CPU23 i can't find module , I need a Help Thanks in advance
-
Hi All i have a trouble with Rextroth servo drive HCS03 iwant amanual or data to know how to connect the digital, analog inputs and digital, analog outputs also i need its software to transfer or modify the parameters thanks in advance
-
Hi All, i have a project containig 3 servo drives what is the suitable and sheapist CPU to safsfy that needs thanks in advance
-
No i cant log into transmit mode the serial cables and parameters are matching
-
the same problem of (communication error - framing error ) i tried the cables above and communication settings but it doesn't work also i updated the software and the problem is still present
-
dear Mr Jojneedw what what the solution ?? isit cable problem or what ??
-
Hi All, i have a problem with CQM1H , The ERR/ALM Lamp is ON and Error log shows a (Memory Error) what can i do ? is it a hardware error? i'm intending to format the memory but the installed program is full of errors while compiling so, i'm afraid not to be able to transfer the program to CPU any of you faced that problem ?? thanks in advance
-
i tried to attach the program file but it failed , can you send me your mail ?? really i have an end instruction
-
there was many end instructions , also part of program is in IL language and full of wrong codes appears as question marks (??????) i don't know clearing the memory will be useful or not ?? i'm not sure if is it hardware fault or software ??
-
yes, a lot of errors (?????) about 1128 errors
-
firstly you should activate the 4th channel you through intelligent function module then write your To From program instructions
-
Nj series SD Card not backing up
Maher Salem replied to Maher Salem's topic in NJ Series / Sysmac Studio
HMC-SD291 2GB -
I have a SD Card on NJ series cpu don't accept the backup I formatted it by using PC and can't do backup from cpu What is the causes ,? Is the formatting by computer affect the SD card ? If there is a password on cpu will it prevent me to format or intialize the card by using sysmac studio ?
-
Dear All, I have a communication problem with S7-200, the CPU Didn't Communicate with Laptop I used MPI and PPI Cable , the Operating System is Win10 What is the Fault ?? 1.bmp
-
thank you so much you are right