Face Book

MrPLC Member
 View profile  See their activity

  • Content count

    47

  • Joined

  • Last visited

Posts posted by Face Book

  1. Posted

    On 4/5/2023 at 1:18 PM, pturmel said:

    Did you enable any kind of routing on the remote end so packets from your machine know how to navigate to the PLC and back?  A VPN itself doesn't provide that.

    Hi Sir,

    Iam confuse about the procedures for Connecting remotely into simatic cpu through teamviewer VPN

    in a certain document in internet " JesperMP "  describes to enable IP routing in remote PC .

    In other document describes to enable IP routing  in office PC.

    In other document,enable IP routing in both PC.

    I do not know what is the correct.

    Can you explain this point?

    Thank you in advance.

    How to setup Teamviewer VPN.pdf

  3. Posted

    Hi Sir,

    Thanks for your reply.

    I saw and read it but did not find the input signal for each button when press it  and the output signal for each button lamp to energizer it.

    Please help me because Beckhoff support not helped.

     

  4. Posted · Edited by Face Book

    Hi,

    In our  filling machine:  the designer installed Beckhoff CP7702-1422-0040

    This CP contains a digital  I/O modules  inside it at the back side .

    Do any member have any docunent or manual that explains how to program the Buttons and the lamps in the front side?

    Waiting your replies.

    Thank you in advance.

    CP7702.jpg

     

    Back side.jpg

  13. Posted · Edited by Face Book

    9 minutes ago, collinsd70 said:

    Are you saying those numbers dont correspond to your actual hardware part numbers? 

    NO

    -----

    I don't find  all of these I/O address in the PLC modules

    ------

    What is the relation between 

    X67BC6321.L08

    and the modules in the table?

    ------

    Module:

    X67DM1321.L08

    and reserve 10 byte

    for digital 16 I/O Module

    How?

     
    •  

  19. Posted · Edited by Face Book

    Hi

    Thank you very much for your support.

    1-Sorry,Iam not understood all the ladder diagram.

    Can you explain it?

    2-Where are the signals of sensor tracking position and rejection sensor  in the ladder diagram?

    3-What do you mean by conveyor indexed signal?

  20. Posted · Edited by Face Book
    Add attached file

    Hi

    1-I will install the rejection sensor and rejection arm followed to detection sensor to simplify the application.

    2-rejection arm will be active for certain time after  the bottle detected by rejection sensor after certain time.

    Can you draw  the ladder diagram for this application? 

    bottle-cap-inspection.png

  22. Posted

    Hi

    Can any member draw  the ladder diagram for this application:

    1-O/P pulse high from the photocell sensor to enable rejection system

    2-Bottle passes in front of another photocell and after certain time O/P is high"rejection arm"for a certain time.

    3-If O/P pulse low from the photocell sensor: nothing to do

    Thank you

  24. Posted · Edited by Face Book

    Hello,

    Thank you very much for your support.

     1- Can you explain  only the last step you did  for remote access to Beckhoff PLC/HMI as attached file with photos?

     

    2-Iam not understand this point:

    " in TwinCAT System Manager when you go to "Add Route Dialog" you have to enter IP address of the PLC in the "Enter Host Name / IP:" field and click on the button (not "Broadcast Search" as if you are searching for the PLCs in the LAN). And yeah, I didn't have 2 network adapters on the remote PC as it is stated in the PDF, remote PC and PLC are both connected to an ordinary ethernet switch. "

    3-Why do you not select:Broadcast Search ?

    4-Explain this point:

    "  I didn't have 2 network adapters on the remote PC"

     You intend :2 Adapters on Remote PC or on Local PC which contains the engineering software tools?

     

    Thank you in advance.

  25. Posted · Edited by Face Book

    Hello,

    Already,I set TeamViewer VPN before.

    Again

    The questions:

    1-Is this  method  applicable for Beckhoff PLC/HMI........?

    as it applicable for Allen Bradley and Siemens PLC/HMI

    2-Can Beckhoff Support confirm this method...?

    In Egypt,Beckhoff support not reply for this question.

    3-What are the procedures to perform this communication?