manna

MrPLC Member
  • Content count

    30
  • Joined

  • Last visited

Community Reputation

1 Neutral

About manna

  • Rank
    Sparky
  • Birthday 08/28/86

Contact Methods

  • Yahoo dmanna3744@yahoo.com
  • Skype dmanna.630

Profile Information

  • Gender Male
  • Location Tangail,dhaka
  • Country Bangladesh
  1. Fx5u Servo(jog Program)

    I am Using MR-J3A Series.I Will Provide The  PLC Program in Attached File, FX5u Raw.gx3
  2. Fx5u Servo(jog Program)

    Dear All Members, I have Colmpleted Servo Programming in Q Series & Fx3u Series.Now I tring to use by Fx5u Module(build in Module).No any Additional Module like PG etc.now Can perform Postioning and OPR Program and Its works.But Problem Is I need JOG Program.and I dont Seen Any Demo Program In FX5u Postioning Manual.Is it possible to write JOG Program?Please Give me a Solution N.B. ------ (All Fx series) Have any Option to storing ABS Current data while Power plug out Then  plug in. i am Using SD 5502 memory to show current Servo data.data gone while replug the power.give me the solutions Thanks In advance 
  3. Fx5u Servo(jog Program)

    Dear All Members, I have Colpleted Servo Programming in Q Series & Fx3u Series.Now I tring to use With Fx5u Module(building Module).No any Additional Module like PG etc.now Can perform Postioning and OPR Program and Its works.But Problem Is I need JOG Program.and I dont Seen Any Demo Program In FX5u Postioning Manual.Is it possible to write JOG Program?Please Give me a Solution N.B. ------ (Fx series) Have any Option to storing ABS Current data while Power plug out Then  plug in. i am Using SD 5502 memory to show current data.data gone while replug the power.give me the solutions Thanks In advance   
  4. FX5U Password

    it was blank program.only i put password for check purpose.but password forget.  
  5. FX5U Password

    i didn't connect with plc.need remote password.if i can communication successfully with PLC then i can reset the password as per your Suggestion .But I can't connect with plc.pls give me solution    
  6. FX5U Password

    dear All, I faced a problem that is password problem.I give a password on my fx5u Plc Couple of month ago.but I can't memorize this password.Have any Option Reset Data?i cant communication with plc.every time ask remote bpassword.Please Give the solution  
  7. MX Component

    i got the solution.now ok.
  8. MX Component

    Dear All, I have a problem in MX Component (Communication setup Utility) Software.When I am going to setup This Software.Every Time Show Error Message.The Message is in  attached File.  I used FX 3G PLC.What i done that i given Bellow through the sequence by sequence______   1.Click The wizard Button of Communication setup Utility. 2.select logic station number. 3.USB select 4.Select FX 3G CPU 5.Select Host Station 6.Write Comments.Then Click Finish Button. but show the Error Message. Please Give the solution.Thanks In Advance. 
  9. fx 3u series plc

    thank for feed back  
  10. I need a potential instruction to work simply.the example is given in attached file.i want to write only one line via a instruction.    
  11. fx 3u series plc

    ladder diagram and GX Works-2 software.  
  12. fx 3u series plc

    I want to add Example(d0+d1+d2+d3+d4+d5+d6+d7+d8+d9+d10=d100)data.have any instruction to save all data to "D100"?.
  13. FX3u-ENT Module.

    I use FX3U-ENET-ADP.When I Select Chanel-1 of Ethernet Parameter of GX works-2 Software.and Write to PLC.After Writing PLC Show Alarm.(Parameter error)
  14. FX3u-ENT Module.

    # Mr. Daniel Thanks for feedback.I Also Try According to your Suggestion.bt result is same(parameter Error).Next what can i do?
  15. FX3u-ENT Module.

    Dear All, I want To Inform U all That I faced A Problem about FX3u-ENT Module.When I Set Parameter(Ethernet Port Option) Of GXwork-2 Software.And Write To PLC.After Write PLC Show Alarm.like Parameter Error/Special Parameter Error. Please Tell me something About it. actually I want To Communicate FX3u PLC(Ethernet Adapter) to Weinview HMI via Ethernet Communication.and I want to Change  IP Address According To My HUB.PLC   default  IP-192.168.1.250 and I Want To Change to - 192.168.104.7(Approx).