tranthanhtung
MrPLC Member-
Content count
48 -
Joined
-
Last visited
Posts posted by tranthanhtung
-
-
do you have list barcode reader that intergrade with CP1H?
Actually, I'm finding barcode cheapest price (~100$ as LS2208 of Symbol).
But, some branch request Keyence, Idec, Mars tohken that x2/x3 price
thanks so much
-
Hello everyone,
I'm studying PLC - CP1H to connect barcode reader.
Do you have any experience to do it, could you share for me some information?
1. CP1H can connect with barcode?2. Which barcode reader type can use ?
Thanks so much
-
On 5/30/2022 at 6:41 PM, VeeB said:Hi tranthanhtung,
You will only specify a start adress (location) where the mac adress will be shown.
If you specify for example write GD150 into GS408. GD150, GD151 and GD152 will contain the mac adress information as shown in the screen capture above.The MAC adress will be shown in Hex I believe and will fit the 3 registers.
Thanks all for your recommend,
I got it.
-
thanks so much Mr.Gambit
However, MAC address have 12 characters ~ 6 Words
Beside, I checked GS408 don't have value (=0)
-
Hello everyone,
I would like check MAC address of GT25/GT27 model,
But, I haven't found special address (GS) that storage it.
who have any information about it, could you share for us?
Thanks and best regards!
-
13 hours ago, krishna k said:Hi,
If you know ip address is it possible to ping with HMI?
Check your laptop ip address also.
Yep, I already ping --> it's ok.
But, can't connect from GT designer, it displayed as first post.
-
3 hours ago, Gambit said:Then the IP adress is probably different than then Default adress.
If there is a utility Switch than you can check what that IP adress is.
If not just read the program via USB first
both default/change IP address are same error
-
Hi,
HMI has program, I want to connect to update program
Via directly or ethernet swtich is same error.
-
Dear,
I'm trying read/write program from GT Designer to HMI (GT2708) via Ethernet.
However, I can't connect with HMI via Ethernet,
It popup messenge as attach file
Who have experience about this, pls share it for me
Thank you
-
-
-
Do you have any recommend for bit that I need enable its to marking where receive data?
I can build it in PLC or script in HMI
Thanks so much!
-
Dear all,
I've already connected Barcode reader to input data for GOT,
But, before using Barcode reader to scan data for GOT, I need press to position where will receive data.
Example: if I want to scan data for Barcode#1 --> I need press to GD2000 --> Scan Barcode#1
Next, Press to GD2005 --> Scan Barcode#2
....
It's waste time press in HMI. So, I would like do as flow: Press to GD2000 --> Scan Barcode#1 --> (data auto fill to GD2000) --> Scan Barcode#2 --> Data auto fill to GD2005 --> ....
Who have experience about this, could you share method for me?
Thanks and Best regards!
-
ah, thanks so much.
I already change config that connected between PLC and HMI ==> and, it's ok.
Thanks for your comment
-
Dear,
I'm trying convert HMI from GT1000 to GT2000 and have issue:
- After convert from GT2000, we can't see/keyin data for words D2000
pls check attach file for more detail./
Who have experience about this case?
could you send for me some advantage
Thanks so much!
-
-
I'm using HMI of Proface and PLC of Mitsubishi, (A series or FX)
could you give me some advantage?
-
Dear,
Sometimes, I check time of Proface's HMI is wrong with current time.
So, I would like setup time for Proface's HMI from PC, daily.
And, I also put this time for PLC that connected with HMI,
Who have the experience about this?
could you give for me some comment?
Thanks so much!
-
Ok, Thanks so much Gambit,
I will try its.
-
Dear all,
I would like study DT-100A of Keyence.
https://www.keyence.co.jp/products/controls/data-logging/dt/models/dt-100a/
But, I only found a little manual of this device.
I can't find manual for setup, it's only inform that need DT-Studio,
https://www.keyence.co.jp/products/controls/data-logging/dt/models/dt-h5/
Do you have any document that explain how to setup to record data from PLC and send to PC (via FPT...)?
Could you share them for me?
Thanks so much!
-
Thanks so much,
But, could you reference for me any documentation first?
Example: What's the documentation which you cut and send image for me?
-
Thanks so much Gambit,
Do you have any document about memory of GOT that explain detail: GD, GS ... of GOT?
Could you share them for me?
I have not found this documentation in Mitsubishi website
-
Dear,
I have HMI GT16, it connected with PC
However, HMI time is difference with PC. ==> And I would like send time from PC to HMI
PC can read time in GS650, but can't write value to GS650.
Could you help me to synchronize time between PC and HMI ?
Thanks so much!
-
CP1H - Barcode Reader
in Omron
Posted
yes, thanks for your supporting
as your comment, we need add more module CP1W-CIF01 for PLC and barcode reader,
seem, it's expensive also. I'm thinking about method to connect via HMI?
Ex: CP1H --rs485--> HMI (Fuji HMI monotouch)
any people test: using LS2208 to read barcode and send to ts1070?