allanleo

MrPLC Member
  • Content count

    10
  • Joined

  • Last visited

Community Reputation

0 Neutral

About allanleo

  • Rank
    Sparky

Contact Methods

  • ICQ 0
  1. Plc2 To Computer Cable

    Hi emd1954, I also have a problem with this kind of plc. We have the taylor software but i don't know how to connect it to the plc2 since i don't have the cable. Could you kindly post your connection to the plc via RS232-RS422 converter? thanks
  2. Hi! anyone knows what I/O server is needed by Wonderware Intouch to access tags from Contrologix5550? If i am to use Rslinx, how do I access a tag form Intouch 7.1? Thanks.
  3. C60K communication

    Hi Jay, If there's a password in the C60K plc, can i still view the program, or do i need to know the Password? Thanks
  4. C60K communication

    Hi Jay, If i use the C500-AP003 together with the handheld programmer, can i browse the program that's already in the PLC(C60K)? Thanks a lot!
  5. NET AIC+ problem

    Finally I made the DH485 Network work!, I just made a stupid setting for channel 0 of the micrologix plc, i set it to DF1 and not to DH485... thanks again philipW
  6. C60K communication

    Thank You Very Much for the replies...
  7. NET AIC+ problem

    Thanks philipW I tried what you said about deleting the RS232-DF1 driver and adding the 1747-PIC/AIC+ driver, whe i did this, i can't see any Micorologix. I used the same cable (--CP3 cable) when i tried to connect again using the DF1 driver, and i see one micrologix. do I need to use another cable when using the AIC+ driver? (see drawing) As for the Panelview300, I have the one with DH485 (with an RS232 db9 port), i made a cable using only the pins 2,3 and 5(without any jumpers for the CTS,RTS,etc) that i connect to the port2 of AIC+, and still it is reporting that there is no node found on the network, the baud settings are correct on the AIC+ and the panelview. Do i have to use a special cable for this? if so can anyone provide me with the pinouts? I tried configuring chanel1 of one of the micrologix to DH485 and connect the panelview to it directly using the cable i made, and it is working.(the panelview can communicate with the micrologix) I'm really out of ideas what to do next. your reply is very much appreciated... allan
  8. I have a big problem with networking 2 micrologix 1500 and 1 panelview300 (with rs232:DH485 protocol) I have 2 net AIC+ converter connecting the 2 micrologix(connected to port 2),and the 2 NET AIC+ are connected to port 3. I cant seem to find the two micrologix in RSlinx if i connect my laptop to port 1 using AB DF1 protocol. I only see one micrologix ,and it is always displayed node 1 even if my Micrologix is configured as node 4 in the DH485 network. If I want to connect the Panelview, where do i connect it, to port 1 of either the Net AIC+? or to port 3? (I have a PV300 with DH485 comm, but the sticker at the back says rs232) Thanks a lot!!
  9. C60K communication

    Thanks very much for your help guys..
  10. C60K communication

    HI!, I just wanted to know how can I communicate to my Omron C60K controller. Do I need to buy a HandHeld programmer?, I Have syswin3.4--> what communication module do i need and how do i install it. Thanks in advance..