kraykov

MrPLC Member
  • Content count

    89
  • Joined

  • Last visited

Everything posted by kraykov

  1. FX5U Modbus communication

    Hello, It is necessary to manage 34 inverters via serial communication RS485. If a Modbus protocol is used according to the documentation, only one RS485 channel can be master. Then the maximum number of inverters will be 32. Can anyone share their experience on this case? Thanks in advance to all those who participated!
  2. Connecting Fx5u

    Hello acansoy. First open a new project. Project ---> New ---> FX5U or Ctrl+N. On the left appears ---> Connection Destination .  
  3. Connecting Fx5u

    Hello acansoy, First open Connection Destination. We choose - Direct Connect to CPU. We choose Adapter - your Ethernet Adapter. By default IP PLC is 192.168.3.250.  
  4. GX Developer analog output help

    Hello @Jkleeds! Can you tell us the model of the controller you are using and the model of the analog module. Then we could give you advice.
  5. Hello Rohit.sadawarte, You can look part 4 - FX5-4AD-TC-ADP at the attached file.The measured temperature value is recorded in a special register SD6xxx. Then you can scale it up if you need it and put it in PID (PV) as in the example of Altan.   FX5_-_User's_Manual_(Analog_Control)_JY997D60501-E_(05.17).pdf
  6. How to add AD or Temp Module to FXCPU PLC?

    Possible only one module FX1N-2AD-BD. It have two analog chanel - current 4-20mA or voltage 0-10V. Its configuration is given below.  
  7. Hi mikax, I can not help you! I'm sorry. The best regards, kraykov
  8. Hello Mikax, I checked the available versions of Medoc and it turned out that I also have only 2.40. There may be missing parts of the program because the ranges for M, L, T, D are not correctly defined. For example, the range of M e 0-999 and in the program we have M1201.     There are cases where the PLC is A2S and the software recognizes it as another. Do you have an extra memory extension?    
  9. It is possible that the program was created and loaded into a PLC with the Medoc DOS version. I could look for her. However, you will need a computer with Win98 or WinXP OS. With GX Developer, the compiler is newer and this is the cause of the problem areas.
  10. I have two questions: Is the machine from which controller you are uploading the program working correctly? What version of Medoc do you use to upload the program?  
  11. Hello @mikax, Probably the project was created on the Instruction List (IL). That's why Ladder Diagram can not properly intercept it. You can try the following - download the project with GX Developer and try to convert it to IL.  
  12. FX5U Modbus communication

    Hello @DanW   I share your opinion on Modbus communication. My client insisted on finding a solution for controlling these 34 frequency inverters on a serial port.   The only possible solution, in my opinion, is to allocate these inverters to the four CH1 - CH4 serial ports and to use the Mitsubishi protocol for communication with inverters.   Still, it is a machine, not an experimental set-up.   Thanks for your advice.   The best regards,   K. Raykov  
  13. FX5U Modbus communication

    Thank you @SolidRio! I will test it.
  14. FX5U Modbus communication

    Hello @SolidRio Frequency regulators are FR-D740, but for 34, two channels are few. 2x16 = 32. Not possible to use CC-link  since the inverters are available and have a serial port. Thank you.
  15. Fx1n control inverter vfd007m21a via fx1n-485-bd

    Hello @huuquyen. There is a sample program in the attached file. He can help you. The best regards, K.Raykov   Program_Example GX Dev.zip
  16. Fx1n control inverter vfd007m21a via fx1n-485-bd

      Hello @huuquyen. The inverter supports Modbus protocol. Select Modbus ASCII mode. The best regards, K.Raykov  
  17. 2 PLC WITH ONE HMI

    Hello Zubair136, There is no problem for a display to work with two controllers. Which model is HMI Weintek? Normally, we have several serial communication ports - COM1 and COM2.It is also possible to add an Ethernet module to the FX2N. Good luck!  
  18. Thermocouple Variation

    Hello, You might want to look at connecting the cables in the picture. Particular attention may be paid to remarks 1-4.
  19. Thermocouple Variation

    Hello, Do the cables you use have a shield? If yes, did you connect it to the SLD terminal in module? Check the connection of PLC terminal PE to the cabinet. The best regards.
  20. Fx3g-485-bd-Rj problem

    Hello Mattyd1211, You can read about your case here http://www.pro-face.com/otasuke/files/manual/gpproex/new/device/mit.htm
  21. fx1n software demo help

    Hello Ulrik, MELSOFT iQ Works is an integrated software suite consisting of GX Works3, GX Works2, MT Works2, GT Works3, RT ToolBox2 mini, FR Configurator2 which are programming software for each respective product. Integration is further enhanced with MELSOFT Navigator as the central system configuration incorporating an easy‑to‑use, graphical user interface with additional project-sharing features such as system labels and parameters. The advantages of this powerful integrated software suite are that system design is made much easier with a substantial reduction in repetitious tasks, cutting down on errors while helping to reduce the overall TCO. (http://www.mitsubishielectric.com/fa/products/sft/melsoft/smerit/iq_works/index.html#pageUnit02). GX Works2 supports FX-1N. Look @Gambit post. What is the problem?
  22. FR-F740P-15K

    You can change the following parameters - Pr. 0; Pr. 9; Pr. 71 and Pr. 80.
  23. How to protect screen with password GOT 1055QSBD

    Here's information about this project: Make: 4.4.2015 г. 12:05:10 ч. (GT Designer3 Ver.1.126G) Update: 27.4.2015 г. 11:22:18 ч. (GT Designer3 Ver.1.126G) Read: 20.5.2016 г. 10:51:17 ч. (GT Designer3 Ver.1.136S) Update: 20.5.2016 г. 10:52:12 ч. (GT Designer3 Ver.1.136S) Read: 14.4.2017 г. 12:29:05 ч. (GT Designer3 Ver.1.136S) Update: 17.3.2018 г. 19:16:25 ч. (GT Designer3 Ver.1.106L) It is possible that part of the functions in the project that GT Designee 1.06L not supported  have been deleted.  Update your GT Designer3 ver.1.106L to GT Designer3 Ver.1.136S and then upload the project.
  24. mitsubishi software

    You're probably joking!
  25. Programming Port

    The interface adapters FX1N-422 BD and FX2N-422BD can be used.