Verdy Adelwin Mahmud

MrPLC Member
  • Content count

    17
  • Joined

  • Last visited

Community Reputation

0 Neutral

1 Follower

About Verdy Adelwin Mahmud

  • Rank
    Sparky

Profile Information

  • Country Indonesia
  1. How to create PID program on FX3G?

    Please tell me about the link
  2. How to create PID program on FX3G?

    GX Works 2 sir
  3. How to create PID program on FX3G?

    Thank's sir. But, I stiil don't understand. I finish make the program scale for analog input (Pressure Transmitter). But, I don't know how to make PID program.
  4. How to create PID program on FX3G?

    GX Works 2 sir...  
  5. How to create PID program on FX3G?

    I wanted to make a PID program on FX3GE This system to regulate air pressure. There is a pressure transmitter must be set at 7 bar and there is an inverter that controls the frequency of the compressor. So when the pressure reads below 7 bar, the motor speed should rise. When pressures above 7 bar, the motor speed must fall. I need an example PID program on ladder diagram.
  6. Positioning Mode (Point Table Methode) Using Servo

    Mr. Luke, I have two method. First, not using sensor. This print using more colour (1-4 colour). Second, using sensor. This print using 1 colour. Sensor mode is second printing from first method. The first method, sometimes it change every positioning operation. Example : I give two condition, bad and good. When the operation run. I found the printouts like this : good, good, good, good, good, bad, bad, good, good, good, bad, good, good, good, bad, good, bad, good, good. It's random between bad and good. The second method using sensor, the feed is too long like my video. I'm very confuse about this operation, I dont know there is a problem in the mechanical or servo program. I hope you understand with my explanation.  
  7. Positioning Mode (Point Table Methode) Using Servo

    Please see the image..
  8. Positioning Mode (Point Table Methode) Using Servo

      Part 3.mp4
  9. Positioning Mode (Point Table Methode) Using Servo

      Part 2.mp4
  10. Positioning Mode (Point Table Methode) Using Servo

    Hi, MR. Luke. I need your help, please see my videos. I attach 3 part video. This servo pull 49mm. The sign of the sensor does not correspond.   Part 1.mp4
  11. Hi, I want to ask, how to make scalling ladder for analog input on PLC Q series. Then I need to know the setting module for analog input.  
  12. Positioning Mode (Point Table Methode) Using Servo

    Oke Thanks Mr.Luke. Yes, the value 695.5 is the circumference... So, the calculation is 6,291,456 / 695.5 = 9045.946800862689mm right?  
  13. Positioning Mode (Point Table Methode) Using Servo

    Hi Mr Luke. I was a little correction. Roller = 695.5mm, It's arround Then, how do I get this value 3.14159 ? That 's phi ?  
  14. Positioning Mode (Point Table Methode) Using Servo

    Oke, I have information like this : 1. Servo Amplifier : MR-J4-350A-RJ 2. Servo Motor : HG-SR352 3. Roller : 695.5 mm 4. Pulley On roller : 3 5. Pulley On Servo Motor : 2 So, ratio pulley = 3 : 2 Servo is used to pull the paper.  This paper used to print labels. I want to pull the servo in accordance with point table. Example : I set target position on point table at 30mm (if set the mm). But now I used pulse    
  15. Positioning Mode (Point Table Methode) Using Servo

    Hi, I have a system using Mitsubishi servo MR-J4-350A-RJ. This servo is used to pull the printing paper. To set the pull, using the points table in the MR Configurator program. What should I set in this servo?