Omronplc
MrPLC Member-
Content count
45 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout Omronplc
-
Rank
Sparky
Profile Information
- Gender Male
- Country United States
-
Thank you for the replied. It turn out I don't have a third disk on this laptop, the last guy that does all the programming for the factory took all the disks. I only have the CX programmer software loaded into this existing laptop, so I would need to get a new NT software to loaded into here. I know the newer version of NTST is 4.8 anyone know the cost on this?
-
Hi Pfort, I got the NTST Ver1.0 and would like to upload the program on my NT11S which has a bad backlight sometime work or would go dimmed. I put it in transmit mode, i did make the cable which you and jay emailed me on here. is there something else I must do to upload the program inside this NT11S? Thx
-
Thank you, it was a SBR that caused all the problem. It is due to no RTN, I have corrected the problem and it is solved. Thx everyone it's been a fast learning for me.
-
I was finally able to upload another program form another machine, I went to transfer it into the Plc and get error problem during compiling? What this mean? If the program that I have uploaded and save had rung problem would it cause this compiling error?
-
Hi Pfort, Whats Ver. NTST will support window XP there was a conflict on the forum on V4.6 or 4.7 can you please confirm this version
-
Thank you again Pfort, you have been a great help for me and I am thankful for people's like yourself and others on here, it's just I wasn't sure when reading this wiring instruction and making sure. I will take your advised and make that cable as you have provided to me. Again,thank you.
-
According to the instruction, please verifiy? RTS/CTS can be connected or jumpered on each end. But, RTS/ CTS cannot be used on Cvxxxx PLCs and MUST be jumpered on the computer side.
-
Yes, my computer does have a DE9 connection and its working. I did make a cable to the diagram that Anthony provided. According to the diagram pins female 7-8 shorted and. Male 4-5 shorted. So there should just be 3 conductors if its a universal cable and this should work?
-
Hi Pfort, According to the Appendix E, I would need 5 conductors but do I use (2) 9 pins or (1) 9 pins and (1) 25 pins I am very confused even after reading the manual. Please explain? Sorry for asking too much, but I am very lost on this cable.
-
Hi jay, I make the 9 pins cable but it didn't do anything after plug into my laptop and nt11s. According to Pfort I need 5 conductors but I looked into this and now completely lost as to which cable would work. Do I need a 25 pins or 9 pins? Very confused.
-
Can you clarify the 5 pins from computer to 9 pin on the NT11S? Is there a cable layout pins for this.
-
Look to me the program that's in this NT11S has a Ver.1.2 and the free download is Ver.1.0 should I still able to upload the program in this NT11S. Or will I need to purchase a newer Ver. Software? I put the NT11S on transmit but nothing happen in the transferring tool. Anyone can help, please do. Thx
-
Thank you for clarified these questions for me. I did read the 115 pages not all answers are understood by myself or I was not sure of. that's why I would like to confirm with anyone on here that might have done this before. I am new to omron, but very knowledge in Allen Bradley. It just seem like there are many steps for upload and download process then AB. So thank you for everything.
-
Can someone please confirm this: to upload the program inside the NT11S i either have to hold down F1 or F4 or both? while power-up to put the HMI in transmit mode.