travis

Does anyone knows how to remove the green box? I feel quite annoying when I saw from the Panel View 1000. It is a numeric enable input box. Thanks in advanced. Have a great day.

Hi all, I want to do an application which PLC send ACSII through RS232/Serial communication to a printer. I want print out my plc data, i can convert them to ACSII but I can't find any printer which can direct received ACSII and print out. Does anyone of you did this similar application before. Any brand or model of printer should i lookout. I prefer thermal printer. BTW, is that possible to do this? Guide me, if i'm going to the wrong direction. Your information will help me a lot. Thank you. Have a great day.

Hi, When I connect my PLC program through VPN, my whole rslogix5000 so laggy. Is this normal? Thanks in advanced. Pang

Hi, I got the device EDS and I have added into my I/O Configuration. How can I know what is the value for the service code, class, instance and attribute? Need some guide, thank you.

Just for testing, I want PLC communicate with the robot. Read or send signal.

Hi, Can I control the Kinetix 300 motion move type trapezoidal to s-curve from rslogix5k? Kinetix 300 drive mode is ethernet. Does explicit messaging instance 273 does it works? Thank you and have a good day.

Hi all, Does anyone know how to filter out those unused tags in program from the controller tags or program tags ? Is there any rslogix 5000 tools or inside the rslogix 5000 able to do it ? Currently the way I do is cross reference from each tags which consumed a lot of time, is there any shortcuts ? Thanks in advanced. Have a great day.

Thanks Michael Lloyd and Ken Roach. Thanks for the information.

Hi all, Does anyone what the difference between kinetix 300 and kinetix 350? What are the advantages and disadvantages? Does any literature which compare of these 2 servo drive? Thanks in advanced and have a great day.

thanks and appreciated for all the information.

Thanks, Ron.

hello all, As title, How to determine the ACD project file is using which version? Is there any method or tools to find out the version to open it? I got a project file but when i opened it shows " Failed to open xxx.ACD. Project file was created with newer version of RSLogix 5000 software." Your solution and guide is much appreciated. Thanks in advanced. Great Day.

Hello, I kinda confuse with the frequency parameter in PowerFlex 40. for P032 is it the line frequency or the motor output frequency? Addictional, How to determine the velocity motor drive by the PowerFlex40, I found out that my of output frequency didn't proportional with the velocity output. The induction motor is running a conveyor belt. If there is a slip, then the result I got shown the slip is very very high which more than 50%. Thanks a lot, great day.

Well, I just familiar with explicit messages and haven't use motion instructions before. This is totally new to me but I'll find out how these works. BTW thanks.

Hi all, I got a Kinetix 300 and a servo motor model MPL-B220T-xxx4. Just wondering how the brake wiring does. Is that okay I just connect the white cable to IO connector pin 49 and black cable to IO connector pin 50 ? Thanks in advanced. Cheers.

Thanks for the help, it does better after I have tuned the motor again. Now I facing new problem, When I cause E19 fault, I'm not able to reset my driver from the program. Only able reset after I cycle power the drive. Have you met similar scenario? Thank you very much, you guys replies really gave a lot supports.

Thanks for the reply. Now I'm done with the brake. Do you know how to shorter the range of velocitystandstillstatus value ? My user unit is 0.1 and my actual speed when the motor is on still condition, it can up to +- 1.2 user units/sec. Is this normal ?

Expression: {tag1} AND NOT {tag2} Expression true state choose : visible or user login, e.g. expression CurrentUserHasCode( A ) Hope you can get what you want.

Shame to ask but I'm curious about it. Does anyone know how this MVM instruction works? and how the math got the result from above picture? Thanks in advanced. Have a great day.

Thanks Alan & Mickey. Thanks for the help. Now I start to get how MVM works.

thanks.

Hi all, Does anyone know what is the value should I put for the "length" operand? Example, I have a UDT which contains 8 real and 1 string20. Should I just put 1 ? I read from the reference manual. It said that " You must test and confirm that the instruction doesn’t change data that you don’t want it to change. The COP and CPS instructions operate on contiguous memory. They do a straight byte-to-byte memory copy. In some cases, they write past the array into other members of the tag. This happens if the length is too big and the tag is a userdefined data type. " Could someone guide me, please. Thanks in advanced.

Thanks man, it works.

Hi all, I'm using FactoryTalk View Studio ver6.0. I try run in my laptop I can see the time & date but when I download into my HMI , they don't show up in my HMI. Is there any method to troubleshoot my problem ? Thanks advanced.

Picture This image is the print screen from my computer. But in the actual HMI, there is only a blue screen without the time and date. so weird ................... HELP me.