gtsuport

MrPLC Member
  • Content count

    1329
  • Joined

  • Last visited

Everything posted by gtsuport

  1. D memory data not moving into instructions

    Is the PLC in Monitor mode?
  2. SCL3(487)

    SCL3 Converts a signed BCD value to a signed binary value. The CP1W-AD041 provides a binary value, not BCD. Are you converting the number to BCD before using the SCL3 instruction?
  3. ID231 and OD232 front connector

    Thank you Michael. Did not find that image.
  4. ID231 and OD232 front connector

    Having trouble finding information on the CS1W-ID231 and CS1W-OD232. I think these are Fujitsu style connectors, but not sure. If you look at the front of the module, Are the top and bottom somewhat rounded, or are the straight?
  5. ID231 and OD232 front connector

    There is no solution for terminal front connectors on 32 point modules.
  6. ID231 and OD232 front connector

    Those are 32 bit I/O modules. There are no front screw connectors available. You will need to use cables (XW2Z-xxxK) and screw terminal blocks (XW2B-40G5).   xxx in cable number = length in meters ie: 100 = 1 meter.
  7. CP1E I/O issue

    Go Online with the PLC. Go to PLC pull down menu, then Transfer, then Compare with PLC. They should match, if not, Transfer to PLC.
  8. CP1E I/O issue

    To force I/O you must be in monitor mode. How are you communicating with the plc, USB or serial?
  9. CP1E I/O issue

    You did transfer the program to the plc correct? gtsuport
  10. floating point shift register

    N = size of data required, 40 for 20 cans. Source D120  Destination D122 After XFER, move new data into D120 After XFER is executed again, all data is shifted by 2 registers. gtsuport
  11. floating point shift register

    Take a look at the XFER instruction. gtsuport
  12. ad041 analog expansion resolution

    Also, looking at the values in the SCL instruction, your MAX scaled value is #64.  Not sure changing the #1700 to #1770 will make any difference. And as IO Rack has said, it may be tied to the calibration of the input device.
  13. ad041 analog expansion resolution

    I can understand your question. At 1700h you are at 98% of resolution.  If you change this, it may affect other parts of the program. Just make sure you understand everything that will be affected. gtsuport
  14. ad041 analog expansion resolution

    Part number of the expansion unit?
  15. TXD data Received by PC show empty/FF FE

    We do not have the CP2E in the US. From the manual, it looks like you could use socket services for the communications. See the W614 manual for more information. Just FYI, I think serial will be easier. gtsuport
  16. TXD data Received by PC show empty/FF FE

    What is the model number of the plc? What port are you using for the communications?  Is it a built in port? gtsuport
  17. TXD data Received by PC show empty/FF FE

    Your TXD instruction is set to transmit 256 bytes of data. Can you receive information? Wondering if your cable is correct.  Omron 9 pin port is NOT standard wiring. gtsuport
  18. How to handle floating numbers in CX Programmer ?

    CP1L will do floating point math, why convert?
  19. Analog Input Addressing

    See manual  W516  Section 8-4.
  20. I think your post is in the wrong forum. None of those are Omron part numbers.
  21. Configuring HSC in CJ1W - CT021

    Please refer to manual W401. That is the manual for the CT021. Addressing will depend on the Machine or Unit Number of the module.
  22. Unable to connect CS1G

    See post on PLCs.net
  23. Omron PLC SYSMAC C60H

    I do not think so. That was a program that Omron sold. It has been discontinued for quite some time.
  24. Omron PLC SYSMAC C60H

    For the Mini H processors, pretty sure you need Syswin or LSS. Syswin will run on Windows XP. LSS was a DOS program.
  25. NT20M HMI prog. terminal

    Look in the Omron Download section on this site. NTM 4.2 should work. Pretty sure this was a DOS program.