patoliyarj
MrPLC Member-
Content count
9 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout patoliyarj
-
Rank
Newbie
Profile Information
- Country India
-
Hi All, I'm testing Cx-supervisor communication with ODT Micropower PMAC controller on modbusTCP. I'm able to establish the communication using ModbusTCP driver with cx-supervisor. But, data I'm getting in is Low word first, so not able to convert properly. If anybody has tried any other option/script for this issue? I did not found any setting in Cx-Supervisor as in Kepserver, shown in attachment below: How can we swap the registers read as a 32 bit word from controller? Thank you.
- 1 reply
-
- modbustcp
- 32 bit registers
-
(and 1 more)
Tagged with:
-
patoliyarj started following ModbusTCP Driver register swap option
-
patoliyarj liked a post in a topic: Questions about CJ2M EIP
-
Hi, PMCR, Yes, it's working.. I've connected 2 FQ2 & one ML1400 with CJ2 on same network for different messaging, & it's working fine.!! Thank you again!!
-
Hi... Thanks a lot... My question is these :All IN THE SAME NETWORK, let me test & revert on it. Thank you.
-
Hi PMCR... I've tested the same as per your instructions procedures & Yes!! It works!! Thank you very much for this detail. One more thing I need to ask you is, on the same network, Can I connect 4-5 OMRON FQ2 Camera Controllers for Datalink access? Might be time sharing basis?? I'm trying to access it now by making CJ2-FQ2 direct connection, but will it be possible to connect all in a smae network to share data?
-
Hi... Thanks PMCR!! I'll test the same & revert to you.. Thank you again..
-
patoliyarj liked a post in a topic: Questions about CJ2M EIP
-
patoliyarj started following C Series Backup Tool V6.0
-
NEW PLC NJ501-1500 machine controller
patoliyarj replied to Yair's topic in NJ Series / Sysmac Studio
Yes, Need not to go with Ethernet Configurator, But if you are used to do that then it's Ok. But, It's very simple & user friendly in Sysmac to configure Datalink for any EDS. I'm not sure, but "Create EDS" option is unique in Ethernet Configurator. -
Hi PMCR, Can you please guide me how to do explicit messaging between Micrologix 1400 & CJ2 EIP? May I write to ML1400 MSG command and CJ side Ladder also? Or any one side will work? I'm having ML1400 with Ethernet built-in & CJ2M-CPU32 with Ethernet. So Need to do via switch or direct connection will work? Please, advise me. Thank you. Raj
-
patoliyarj liked a post in a topic: Questions about CJ2M EIP
-
NEW PLC NJ501-1500 machine controller
patoliyarj replied to Yair's topic in NJ Series / Sysmac Studio
HI, Yes, Sysmac Studio is now upgraded & better compare to initial versions.. But still start-up time for software is still higher. Many new functions added, especially editor/variable management side & continuous improving. No comparision to Cx-P as completely different platform including IEC 61131-3. Most of Cx-P short cuts are as it is. Also you can configure the same like in cx-p. Using since ver. 1.01, updated to v1.09. Also robotics & Kinematic FB for Delta type parallel robot programming, if robot option is installed. Vision Camera series FH is on sysmac, so single software for PLC Logic/Motion/Vision/Safety/Robotics. Overall very good platform & something new in Omron's basket for tomorrow's Machine manufacturers... -
Can anyone have GTD 5.15? I need to communicate with GOT970 in a old machine. I've also read somewhere, GTD 2 Classic also work with GOT900. Please, advise me for the same & help me out to made this possible. I'm having GTD2 & GTD3 with me. Any add-on can work for me? Thank you.