mahmoudsaed19
MrPLC Member-
Content count
15 -
Joined
-
Last visited
-
ramadan goda started following mahmoudsaed19
-
Hi everyone Can anyone help me with NT Support Tool as I am programming my first NT11S Programmable Terminal , I read the manual , I understand the control area but i do not understand the function of notify area and the mark table ,so can anyone help me to explain those and if there is anything else that i should adjust ,thanks every one
-
thank you , i try and it works , now i compile and no error. thank you again and also thank for geir and for pfort for their interest
-
i am using cx programmer v 8.1 and the error appear in compilation happen when i try to compile before i start to download the program in the new plc unit , i do not how it is not make any error as when i compile it give me the warning you talk about and at end error in function block area saying : missing ) what you mean about the other plc unit v.3 or v.4,you mean the cx program or the new plc unit so if you can help me i will be grateful, thank you
-
i have a PLC program uploaded from a working machine , after the PLC broken i try to download in another PLC but it gives me error in compilation in the part of the function block , it gives me error : missing) . so if any one can help me with this error , i attach the program so that any one can see the error when he tries to compile the program , knowing that the PLC is CJ1M cpu 21. thank you everyone.program.rar
-
OK , thank you , i will try and ask you if i have a problem . thank you again
-
is it installed automatically or it need a driver CD?
-
thank you Jay and thank you PP for your reply i already have cx designer so i will try to upload the program but is it with that simplicity? and i don't need to do anything in the interactive display to start upload ? thank you again Jay and PP
-
sorry but where the reply
-
HELLO can anyone help me with OMRON-NS5_MQ10_V2 Programmable Terminal , as i have one in machine in my work and its interactive display is broken so i want to upload the program from it to download in a new one so i hope anyone help me for that . thank you everybody
-
thank you for your reply , i will try your suggestions and tell you about results , thank you again
-
hello everybody can any one help me with plc omron cqm1h-cpu51 , i tried to upload the program from it but it always give me ( connection failure ) , note that i tried uploading with cx program version 5 and version 7 and the same problem and also i tested the cable i use in another plc ( cj1m CPU 22, cqm1h CPU 22) and it worked correctly so can anyone help me with that, as it is necessary for me to upload this program , thanks for everybody. note that this is what is written on the CPU unit : OMRON CQM1H - CPU 51 programmable controller CPU unit in 24 V DC , 10 mA , 16 point made in Netherlands
-
thank you very much for your helpful information it helps me very much i will start with manuals you attach and if i have any thing unclear for me i will ask for a help. thank you again for your help and time
-
thank you again it starts to be clear to me . so as you say if i want to communicate between PLC and a terminal like NT11s for example there isn't a special commands for that i just use the addresses i set in the terminal directly . the difference only if i want to communicate with computer. is it right what i understand ? and if i you can tell me the name of the manual to communicate with computer or attach it for me it will be helpful . thank you again for your help
-
thank you for the manual and the program i will start with them and if you have any thing to help me to can use the host link and NT link in plc CQM1 and how use them in programming i will be grateful thank you again
-
i am a beginner in the plc and i have terminal omron NT11S and plc CQM1 and i want to know how to program the terminal first and the cable used for and how to make connection between it and the PLC and how to send and receive data between them and how to use the hostlink in the plc .