servo_hunts

Thanks it's working

Dear, How can i print the Alarm History in E1101 HMI? i don't want to print individual alarms when it active but i have to print bunch of alarms when i want. HMI: E1101 Printer: EPSON E300+ PLC:FX3U Servo Hunts

Dear All, How can i use "multiple CALL" function in same POU & "1msec timer interrupt" in GX Works2? Regards Servo_Hunts

Dear, Please follow the step given below 1>Power OFF the HMI and remove HMI battery. 2>Power ON the HMI and Check the display screen If screen is still not getting then that's hardware problem.

I used d FX3U-32MT PLC with Structured programming in GXW2. Pls explain following 1> How can i used 1msec timer intrupt in Structured programming? 2> How can i configured multiple subroutine(i.e. CALL function) in single POU?

Dear All, Is it possible to use label in GT1000 Series? I used the GXW2 and GTD3 in my project. For ex.i used "temp" variable in plc.can i define the same variable in GTD3 directy(i.e.without using PLC built in Devices)?

How can i set the FR-A700 VFD parameter in MT Works2 with Q173D cpu?

Dear, How can i set the FR-A700 VFD parameter in MT Works2 with Q173D cpu? Is it possible to set the all VFD parameters without hardware?

Is it possible to perform positioning control by FR-A740-**** vfd via SSCNET III (FX3U-20SSC-H)? Hardware Details: FX-3U-16MT FX3U-20SSC-H FR-A740-**** VFD FR-A7-AP FR-A7-NS MR-J3-40B SERVO

Dear All, Is it possible to Torque Control for Winder in MR-J3-B Servo with QD75-MH2? Servo_Hunts

Dear, > increase the baudrate..... > change the DC bake related parameter i.e,Pr.10,11&12. > Use of brake resistor is advantage in ur application. > Use creep speed > Use high speed compare instruction in PLC and stop the drive through interupt generated by high speed comparison ins.

Dear All, Can i used Servo Motor(any mitsubishi make) with Variable Freq. Drive(FR-A740 Series)? !!!!!!! Forgot about application..!!!!!!! Thanks

Dear All, Which Programing cable & software i needed for FX2-64MS Triac Output PLC programing? Servo_Hunts

Dear, i have a GX Developer software ver. 8.91V,but in plc type FX2 option not display so which version i have to used. thanks Servo_hunts

Dear All, Can anybody tell me the following specification of Mitsubishi Make HF-SE-52 servo motor 1. How much overload the AC servo motor can take for 1.1 Less than 1 min time 1.2 For 3 mins 1.3 For 10 mins 2. Amplifier has inbuilt overload protection. Please give details like the protection provides for sustaining how much overload and for how long ? 3. What is the allowable maximum load inertia moment ratio servo motors? 4. What is the maximum % instantaneous torque the servo motor can handle without any damage and slip in servo functionality ? ( Note : Motors do not run at more than 190 rpm) 5. What is maximum allowed peak load ratio ( in % ) for momentary ( less than one minute ) condition ? 6.Can these motor be run at 85 % effective load ratio if the motors are running at less than 200 rpm ? Servo Hunts

Dear All, Anybody know that how to connect the sensor at FX1N-60MT-001 input ? I am used the NPN sensor with external +24v SMPS for sensor. pls find the attached terminal details of FX1N-60MT-001 PLC. Thanks

Hi, Used the Device Address above "PRM1000"(For EEPROM) instead of "PRM0" .Means for Pr.3 you have to used PRM1003 address but Frequent change to EEP-ROM data may cause, the permissible write times (1 million times) of EEP-ROM to be exceeded, leading to a failure.

same one i checked with GT WORKS3 and GX WORKS,it's running properly. Servo_Hunts

Dear All, Can i check the Automatic refresh setting in multiple cpu system using simulator of melsoft navigator(melsoft iQ works)? Servo_Hunts

I already set the autorefresh setting in GX WORKS2 and MT WORKS2,but in simulator i have to checked that if i will Forced ON "M0" bit from PLC then will i get status of that bit in motion program OR not?

Dear, Take the encoder feedback from master and connect into slave pulse train input.For master/slave set the slave servo into position mode and set Pr.21=0012(A/B phase pulse train).Also u have to set Pr.3,4 &27 as per ur application. Servo_Hunts

THANKS

DEAR ALL, PLS TELL ME THAT, WHAT IS THE DIFFERENCE BETWEEN Q38RB & Q38RBE? REGARDS SERVO_HUNTS

Dear All, Where i have to found d manual of MR-J2-60D SERVO? Servo_Hunts