biglam106

MrPLC Member
  • Content count

    17
  • Joined

  • Last visited

Community Reputation

0 Neutral

About biglam106

  • Rank
    Sparky

Profile Information

  • Country Vietnam
  1. Find GSD file of Wiedemann

    Dear all, I use device of Wiedemann. but not has GSD. Pleasea give me GSD of device below: Synchro III SAB Welle 880-00083 (Pleasea see picture attachment) Pictures.rar Please help me Thanks & best regards, Biglam
  2. CQM1H to 3G3MX communications

    i use TXD and RXD to progra. it is ok. thanks everyone
  3. CQM1H to 3G3MX communications

    hi Jay ! i have known RS422/RS485 of 3G3MV inverter is Modbus protocol on chapter 7 It clearly describes protocol frame. If you use CS1 / CJ1M / CJ2M /CP1L with communication unit, you can use CX-Protocol and protocol macro to communicate with inverter easier. CX-protocol does not support CQM1H, so I must use TXD & RXD command. but i dont code program for this one. so everybody can help me ! thanks jay & everybody
  4. hi all, i am testing communication between CQM1H-SCB41 to inverter 3G3MV (RS422). but have a error CAL from inverter when i set parameter n003 = 2 and n004=6. i setting port B of PLC (please see attach file) and inverter : N002= 0 N003= 2 N004= 6 N151 =0 N152 =1 N153= 1 N154 =3 N155 =2 i don't know use instruction to program (TXD and RXD or PMCR) and my configuration is correct and use PMCR instruction ? please show me or send me code program use cx-programmer to write frequency from PLC CQM1H to inverter 3G3MV and read frequency from inverter to PLC thanks everyone so much. i am hearing from everyone soon. best regards, p/s : my email : nguyenhoanglam106@gmail.com and sorry my English is bad
  5. hi everybody i have a new project with magelis of scheneider. but now i have a problem : i can not upload from old MAGELIS : XBT F024510 TO PC beccause i don;t have software : XBT-L1003 if you have it, can you share it with me? please help me I AM LOOKING FORWARD FROM EVERYBODY SOON thanks you
  6. thanks aggattapauer now, i want to transfer progmmer from old MAGELIS : XBT F024510 to PC please tell me what cable and software do I must use?
  7. thanks you crossbow i have some questions , i use PLC is TSX P57253 and HMI is XBT GK5330 please tell me what cable do i use in this case : 1. PC <------> PLC 2. PC <------> HMI 3. HMI <------> PLC thanks you very much look forward to hearing from everybody
  8. hi everybody ! i have a problem, please help me now, i want to use new magelis , it is XBT GK5330 but old program inside old magelis ( XBT F024510 ) and i dont know how to convert program from old magelis to new magelis ? please help me , i have just attached this file, please see it thanks LIVE_VER.rar
  9. hi every body ! i have a problem i don't understand this code ( demos files " bakery" ) if FlourTank < 100 && !MoveMan then MoveMan = 1 endif if MoveMan then if MoveMan < 5 then MoveMan = MoveMan + 1 else MoveMan = 1 FlourTank = FlourTank + 10 endif my question is : 1. MoveMan = integer ( 1 to 10 ) and ( ! = not ) therefore the code "!MoveMan" = what's this ? 2.this code follow : if FlourTank < 100 && !MoveMan then MoveMan = 1 value = what's this ( boolean or integer ) 3 this code follow : if TankOpen && FlourTank then MillerOpen = FALSE if Miller < 100 then FlourTank = FlourTank - 5 Miller = Miller + 5 else TankOpen = FALSE endif else TankOpen = FALSE endif - tankopen = boolean - flourtank = integer => why to use " TankOpen && FlourTank " therefore what is new value of the expression ? please help me ! thank for reading looking forward answering
  10. SERVO MOTOR

    It depends on your machine. Calculate the transmission from the motor to the final motion, to discover how many cm is one motor turn so, i must know following parameters : • Deceleration rate • Ball screw pitch • Pulley diameter, etc. but, i dont know how to know "Ball screw pitch" maybe omron gives us it or we must use screw pitch gauge i attached picture , do you think about it , can you explain for me thanks
  11. SERVO MOTOR

    hi you i don't understand your idea very much now, i use the first in this case 500 p/r means if we set up 500 pules , servo will turn 1 over now i want to move 10cm, how many pules do i set up ? should we rely on feedback from encoder ? sorry my english is very bad
  12. SERVO MOTOR

    hi everyone ! can you tell me how to calculate the number of pules for servo motor R7D ? what do we rely on to set up the number of pules?( maybe , relying on axis of servo or experience ) i look forward to hearing from everyone thanks everybody once again
  13. don't use Line Graph Objects

    SORRY EVERYONE , I AM RESEARCHING IN OMRON WHILE I AM A STUDENT , SO MY KNOWNLEDGE IS LIMIT AND MY ENGLISH IS VERY BAD TO DESCRIBE MY IDEA FOR YOU TO KNOW THOROUGHLY. YOU SHOULD BE MORE SYMPATHETIC TOWARDS ME I SEND MY EXAMPLE TO YOU I USE ADDRESS D100 BUT NS5 DON'T SHOW HELP ME THANKS GRAPH_.rar
  14. don't use Line Graph Objects

    hi-pdl i want to draw current from inverter. i want to use np5, but i reget NP5 is not widely available, at least not in Europe. so, you can show me draw current with hmi ns5 thanks you very much look forward your answer soon !
  15. don't use Line Graph Objects

    everyone help me, please i want to draw current on HMI NP5 i used " Line Graph Objects" but can not please, give me some example ( i have CP1L AND NP5-SQB0001 ) thanks