BENNDER

That works. So simple, as that. It had proven of everything, and looked for some conversion tool But that didn't have him pro I supposed that one was not able to, since there was not the NT631 Thank you again.

Hello to all. I am trying to convert the code from a NT600S to NT631C I use NTST4.73E, but she doesn't appear in to the options of changing PT, she only gives me the option of change to a NT620 Does somebody know if it is possible the change to NT631C? The end objective is to convert to NS8, using the tool of Ns-Desiner 6.0 "NSCnv_NT.exe" But this application, only admits as entrance format NT631C. Some suggestion?? Thank you.. greetings.

Hello! they are happened two forms to calculate the time that the alarm has lasted. 1ª) To the beginning of the alarm, to Keep the hour, it dates current in a channel. When concluding the alarm, to subtract the kept value of the hour, it dates current. 2ª), maybe but easy. To the beginning of the alarm, to Put to zero an accountant, and to go increasing it, each 1s. at the end of the alarm, we will have the duration in seconds. For the second part, lalectura of the file in CF, I don't understand very well that it is loq eu you want to make.. * To look for files whose creation date is previous to 4 months? * To look for annotations inside the file of more antiquity?? greetings.

Hello. To my I have been presented the same problem with CXS, but not alone with that.. there are many other programs that don't allow to coexist two different versions in oneself installation of S.O. The solution for the one that opted, it is generic: 1) you make a second partition in the Hard disk. In my case, I have Three 1) S.O. 1 2) S.O. 2 3) DATA 2) if you don't want install everything again, simply copy the 1ª in 2ª, with an appropriate soft, for example the GHOST of Symantec 3) a Soft of multiple outbursts installs, (him but simple possible) for example the OSL2000 Although it can seem a drastic solution, it is the only one sure for that if not never these insurance that problems don't arise with some DLL of the different versions..

A quick guide of programming for NT11S In the p. 9 of the document are indicated as selccionar digits with sign. guia_rapida.doc

The files. OBJ contains the part of code of the PLC. They are used in the cards CF. Concretely if it is loaded in the card a called ficehro AUTOEXEC.OBJ and a microSwich combination is used in the plc, this code will be copied and executed in Power-ON of the PLC Memory_Card_2.pdf

PIDAT is not an instruction admitted by CX-Simulator. http://forums.mrplc.com/index.php?showtopi...hl=cx-simulator Regards. Bennder.

Have you checked if he/she is making the I compute x2, in both flanks of the pulse???

Yes! . It is possible. There are two instructions to read and to write in the card that they allow you to take out their content to the memory of the PLC. FREAD FWRIT Unfortunately, the transfer of data toward / From the card only 1024 Byts/seg. approximately.

Hi ! The limitations to use ETH connect to NS to PLC are those of a network ETH that is to say 100m among nodes if is used cable or 200 to 300m if is used WiFi. This distance can be duplicated interspersing stations of repeat (Swich, or AccessPoints ) Regards

Chris, As is the light?? Fixed or blinking?? If it is Fixed, signifies that not this well configured the board I/O of the CPU If blinks, signifies that itself him there is asigned an IP does not validate or in confilct with another in the NETWORK.

Hi. Yes . I Have two. MOVD (083) [ S,C,D] XFRB (062) [ C,S,D] Were, S= Word Source. C= Word Control and D= Word destination. Is not a single instruction, that will be run two, one for every mov of byt. Manu_Ref_MOVD___XFRB_CJ1M.pdf

Hi. That I modulate you use?? The series CJ (CJ1W-OD211) has in the diode inside, as can be seen in the PDF, pag 542 and 543. It is recommendable like says BobB, not to control directly with the I module, by means of a rele or external transistor. One must respect limit him of Volts and Amps of the I modulate in any case. MANUAL_Operaci_n_CJ1M.pdf

Hello to all! I work with CJ1M CPU13 Ver 3.0 of CPU My problem is that to use the instruccion BAND (Dead Lan) the channel at the outset of the intruccion, to stops functioning. It can change its value directly in the memory (W) but if you execute any operacion on the, for example: MOV + 10 Channel, the value of this does not change. This it is maintained until you Bring up to date the board I/OR of the CPU. Only it occurs despues of to have executed BAND giving as destiny that channel. The problem is not solved Resuming the CPU. Only occurs me with the CPU V3.0, with the V2.0 functions well. Someone knows some problem with this instruccion?? Many thanks. Greetings.

Hi! With the browser WEB, is only possible to See and to modify parameter of the ETH. He is not possible to agree to zones by memory, program or I/O. In the version he Integrated with the CPU he is neither possible to do FTP neither mail.