Stupidav

MrPLC Member
  • Content count

    111
  • Joined

  • Last visited

Community Reputation

-1 Poor

About Stupidav

  • Rank
    Sparky

Contact Methods

  • Website URL http://

Profile Information

  • Location Southwest Michigan
  • Country United States

Recent Profile Visitors

2071 profile views
  1. Compact Logix Module Config Changes

    Thanks after reading your post the module does restart but fortunatly the Compact Logix doesn't worry about that too much so everything kept going.
  2. I have a 1769-HSC rev A on a Compact Logix system. I can't seam to remember and my searching has come up short. I need to change the Mode of the Ch0 input, will this require the controller or module to restart? Currently we can't take this system offline or even restart it at this point in time and I don't want to mess up and since I can't remember, any help is appreciated!!!
  3. Honeywell HC900-C50 Error

    We have a Honeywell HC900-C50 that randomly faults out and so far the only thing I have been able to determine is that it is an "Abort Error", or at least when it is flashing red 3 times. I have been told that it has come up and flashed 2 times red, but I have not seen that yet. Here is something that stood out to me, although I don't know what it means: Hardware Okay - OFF ???? FYI: CPU REV. 2.1 Code REV. 2.3 I thought I had read that the program had to be the created for the proper firmware otherwise it would potentially cause a fault, although I am not sure if the above is pointing this out or not. Ant help is greatly appreciated!!!!!!!!!!!!!!!!!!!
  4. CNC Controller

    Thank you very much.... I will start lookiing, I never thought about looking at the "Fine Print".
  5. CNC Controller

    Has any one seen one of these? If so where can I find any information on this. AB says that they don't recognize the any of the information. Any help is greatly appreciated!!!!
  6. ML1400 Current Series?

    What is the Current Series of the MicroLogix 1400's, in particular a 1766-32AWA?
  7. ML1100 connection to C300 Panelview options?

    It might vary a little depending on the cable that you are currently using. If my memory serves me right, on the PLC DB9 connector Pin 2 goes to Pin 3 on the DB9 of the screen then from Pin 2 on the screen most likely goes to Pin 3 on the Scanner then from Pin 2 on the scanner it would go to Pin 3 on the PLC. Pins 2 and 3 are the Transmit and the other is Recieve for most devices. From what I remember the PLC does use some of the other pins as well, and you will have to check the scanner to se what it requires. Something along the lines of the picture should work. Just verify the scanner output.
  8. Component PanelView Issue

    I am getting closer. I am starting to think that it is a setting with in Internet Explorer. I tried it on a different computer and ended up with all kinds of different problems, then on a third computer and everthing worked perfectly. Now I am just trying to narrow down what the differences are between the computers.
  9. Micrologix 1400 Delivery Problems

    I know this thread has been out for a little while, TW I haven't had any trouble getting any of the modules, The only thing I haven't been able to get is a MicroLogix 1500 Base, in any configuration (AWA, BXB, BWA...) If any of you are still looking for a 1400 I do have one on the shelf in a factory sealed box, I can sell if you really need it.
  10. ML1100 connection to C300 Panelview options?

    You can Daisy Chain the serial Just make sure the Node Address is different on each device. I can't remember how many total devices you can get but I know it is more than 3.
  11. Component PanelView Issue

    Has anyone seen this error before, when attempting to access the Communication Tab via the Editor. The what is strange to me is that I only have this problem with New Files. Any old ones that that were previously functional I can access everything without a problem, it is only new programs that I am having trouble with. I know it has been 6 months since I have used one of these but I can't seem to figure out what I am forgetting. Any help is much appreciated.
  12. Ultra 200 Software

    I have been looking for a while now and have been unable to find the software for the Ultra 200 Series Drives. Does anyone know if it is still available on Rockwell's web site?I thought it was called UltraMaster, which I have found all kinds of things with exception of where to get the software. Any help is greatly appreciated!
  13. Understanding / Learning S5 Logic

    Here are the Files NONAMEST.zip
  14. Understanding / Learning S5 Logic

    I can post the S5 Files if that Helps
  15. Understanding / Learning S5 Logic

    Back to where I got Lost..... I think I am on track, BCD : FW 48 SBCD : F 60.2 DUAL : FW 50 :L KM 00000011 11100111 :L FW 50 :-F :T FW 52 This is Taking FW48 and F60.2 Converting them to FW50? Then subtracting FW50 from 999 (in binary) placing the result in FW52, Correct? Then :JU FB 241 Name :COD:16 DUAL : FW 52 SBCD : F 60.2 BCD2 : FY 61 BCD1 : FW 18 This is just converting the answer back to BCD, Correct? Then :JU FB 5 Name :GROBDOS. ANGR : FW 24 ZD+ : F 8.2 ZD- : F 8.3 FRUE : F 7.0 WAAK : I 1.5 ENTL : Q 9.2 KLS : Q 10.1 This is Jumping to FB 5 Which uses the next stuff, but the next stuff I don't have a clue. Just incase I am attaching the Print out of the program if that helps. Buehler.pdf