Jaime_Caballero
MrPLC Member-
Content count
24 -
Joined
-
Last visited
Community Reputation
0 NeutralAbout Jaime_Caballero
-
Rank
Sparky
- Birthday 03/17/73
Contact Methods
- Website URL http://
- ICQ 0
Profile Information
- Country Mexico
Recent Profile Visitors
2060 profile views
-
Hi to all I have a new Elektrobit (formerly JOT) equipment FIFO J214-50 that has installed 1 NT 20 Touchscreen and PLC CPM2C It's the firts taime I work with it so the problem is this: When the equpment is turned on , on screen appears "Main Menu" with 5 differents options to make adjustments, then , when I press one option (i.e. Configuration) , screen changes to that screen menu, but 2 seconds after , it backs to "Main Menu" , so , it doesn't allow me make anything , either calibrations and references routine . I just want to be sure if this kind of problems is technical with OMRON devices are used or it has to be something related to whole equipment itself. BTW , talking about Elektrobit Equipment , does anybody on this forum have worked with Shuttle J208-50 , also I have problems with it. Thanks a lot for your help BR
-
Hi There!!!! I hope you're well I'm bothering to you again by insisting on MiniLSS SW. I installed Microsoft's Virtual PC (45 days-trial) demo , with MS-DOS 6.22 . MiniLSS seemed to work well by communicating and even monitoring programs , now , a new problem appeared in compile step. It seems that the program was unloaded , when I go to De-compile , it ask for program name and start to de-compile , some message appears ( loading blocks 2 , 3....etc ) , then a black square appears with legend "Info >Project" and then nothing can be done . I have to close an re-open MiniLSS , with same results. Cpukiller is used during the process. Does anybody have similar situation , or tried to use Virtual PC for MiniLSS. Thanks for your help!!!!!
-
Hello Everybody!!!! I need your help to find a place in the universe to get MS-DOS or DOS . I'm preparing a laptop for hard disk drive partition in order to install MS-DOS or DOS for MINILSS at one of them , other partition for Win XP (Syswin ,CX-P , etc.)and all that stuff. Where I could get it ???? Thank in advance
-
Hi 2 all I need somebody's help , since I'm worrking with MINILSS. I need to upload a program from a PLC and I'm checking steps on Quick Help MiniLSS. Regarding upload I don't have problems , they appear when I get compiling Obj>Diagrams , after select that , MiniLSS screen hangs with a small block in the middle telling "Info >Project" Thanks in advance Have a good life
-
Hello Everybody I will start to work in a project for a semiautomated glue dispenser that requires rotary movement. I got from SureStep the motor (STP-MTR-23079) and the controller card (STP-DRV-4035), and the PLC is CPM2C 20 IO with relay outputs. Thais is the first time dealing with this kind of project, so I'd like to know what considerations I need to know before start , and also I need to know where I can learn regarding servocontrollers and PLC connections. Thanks in advance BR / Saludos
-
Hi Everybody I got a floppy disk that contains the program for a JOT stacker. I tried to download this program to PLC , and download seems OK , but almost the end , a error window appears saying that "expansion function has errors (or something like that) , check dip switches or PLC Setup" Before download , on prompt window , I select expansion , because it's already using the 24EDT unit. I see the small switches on PLC but I don't know which position is the correct for downloading. Actual position are both OFF. Thanks
-
Hi There!!! I've have many JOT conveyors using old SK20 PLC, and I've not been succesful to run MINILSS in laptops with W2K , I will start to use the Prog console to work with them , but I'm not sure which is the right one (cable too) to work with this PLC model? BR Thanks in advance
-
Hi youyou25 I have problems by sending fax to you , so I got a very roughly drawing from cable's internal pin connection. Just try it and let me know any issue with it. BR CablePC2PLCCXXH_K.doc
-
Hi Youyou25 If you have a fax number, I can send to you a diagram to built a cable for PLC C**K/H Is a normal 9-pin female to PC and 9-pin male to PLC. I 'm confident it will help to you and save some money. BR Jaime Caballero
-
BENNDER Donde o como consigo el Memtest que mencionas? Saludos Courtesy www.freetranslation.com BENNDER Where or as with himself the Memtest that you mention? Greetings
-
Hi everybody I have a problem with CX-P 4.0 I'm installing the software package on a Laptop IBM T23 with Win2000 Professional, so , the installation was normal , cx-p ,cx-server , plc tools ,etc. , After installed I launched the program, when I went to File-New, a blue screen with a memory dumping error appeared for 1-2 seconds , then , PC was restarted. I changed the CD unit for test and it was the same thing. After that , I installed the CD on an older laptop IBM 600E , and it worked fine. For last , I installed in my work's PC desktop, and in runned without problems. What else I can do. Thanks for your help. Saludos
-
Hi Everybody Last month I had a severe PC virus infection and crash down , losing Internet and e-mail info I used to have to get on line. Now , its seems everything is normal again and I am in the field again. I can't remember who was , but before the shutdown , someone asked me about the settings I used for minilss in my Win98 laptop. Can someone get me in contact with him/her and try to help on it? Thanks in advance Best Regards
-
Hello There !!!! Could someone help me how can I know how many DM are used in the current PLC I'm using and how many are free? I heared something about Cross Reference capability , but I didn't catch it up at all. I'm using CX-P V3.0. Thanks in advance for your help Jaime Caballero Reynosa ,Tamaulipas Mexico :